Problem 2: A concrete one-way slab has a total thickness of 120 mm. The slab will be reinforced with 10 mm diameter reinforcing steel bars with fy = 276 MPa. Concrete Strength f'c= 21 MPa. Determine the required spacing of 10 mm RSB if the total factored moment acting on 1-meter width of slab is 25 kN-m. Clear cover is 25mm. Reduction factor is 0.9.

Problem 2: A concrete one-way slab has a total thickness of 120 mm. The slab will be reinforced with 10 mm diameter reinforcing steel bars with fy = 276 MPa. Concrete Strength f'c= 21 MPa. Determine the required spacing of 10 mm RSB if the total factored moment acting on 1-meter width of slab is 25 kN-m. Clear cover is 25mm. Reduction factor is 0.9.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Concrete beam.
Describe the steps that an engineer should follow if you were asked to determine the need to design a new highway to replace the current one.
Design Problem 1 & 2 Determine the cracking moment for the prestressed beam section shown if f'c = 35 MPa. Use a modular rupture of fr Assume normal weight concrete. = 0.621√ f'c C = 100 mm b₁ = 350 mm D = 125 mm d = 440 mm h = 500mm b₂ = 200 mm Figure 1.0 Cc 60 mm C-150 mm h, 250 mm b₁ = 250 mm b. =350 mm Figure 2.0 d 630 mm h = 700mm Ce 70 mm
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the tensile steel ratio for positive bending. 2. Determine the depth of the uniform rectangular stress block on the beam section at ultimate stage when subject to positive bending. 3. Determine the design moment capacity in kN•m of the beam in positive bending.
Problem #1. The base of a rectangular reinforced concrete beam is 300mm and the effective depth is 550mm. Concrete compressive strength on the 28" day is 24MPA and steel yield strength is 415MP.. Determine : a. The depth of compression block (in mm, 2 decimal places), the strain in the tension steel (5 decimal places) and ultimate moment capacity (in KN.m, nearest tenth) of the beam if it is reinforced with 4-32mm diameter bars. b. The depth of compression block, the strain in the tension steel and ultimate moment capacity of the beam if it is reinforced with 4-20mm diameter bars.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only. 2. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
Pre-stressed.
SITUATION IIl: A reinforced concrete beam with a cross-section of 250mm x 460mm (60 mm steel cover). Use the following properties to calculate what is required: f'c = 20.7 MPa fy = 344.7 MPa %3D As = 3-36mm A's = 2-25mm 8) Draw the stress diagram of the beam section 9) Calculate for the depth of the compression block. 10) Calculate for the compressive strength of the concrete (in KN). 11) Calculate for the nominal moment capacity of the beam.
Correct solution
What is the threshold torsion (kN-m) of a rectangular beam with a width of 446 mm and an over-all depth of 536 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 75 mm. The specified compressive strength of concrete is 22.00 MPa. The yield strength of tension reinforcements and stirrups are 404 MPa and 323 MPa respectively.