Answer using Bond development length hooks and splicing of reinforcement in RCD NSCP 2015. The answer is A) 1257mmB)Ld=866.614mmI need a complete solutions with step by step.. PROBLEM 10.2:A 3m wide wall footing supports a 300mm wall. It is reinforced with 20mmo bars with concretecovering of 75mm. If f = 20.7 MPa and fy = 414 MPa,a.b.Which of the following gives the available space for development.Which of the following gives the required development length.Ans: 1275 mmAns: La = 866.614 mm

Answered: Image /qna-images/answer/6d597ae7-8c0a-483f-a21d-a582577c4e10.jpg

PROBLEM 10.2: A 3m wide wall footing supports a 300mm wall. It is reinforced with 20mm bars with concrete covering of 75mm. If f = 20.7 MPa and fy = 414 MPa, a. b. Which of the following gives the available space for development. Which of the following gives the required development length. Ans: La Ans: 1275 mm 866.614 mm

PROBLEM 10.2: A 3m wide wall footing supports a 300mm wall. It is reinforced with 20mm bars with concrete covering of 75mm. If f = 20.7 MPa and fy = 414 MPa, a. b. Which of the following gives the available space for development. Which of the following gives the required development length. Ans: La Ans: 1275 mm 866.614 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two wood boards, each 18 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 1080 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 4.2 kN. Use a = 18 mm and b = 144 mm. d Glue b P P Answer: d = i mm
Determine the x-bar centroid of the composite figure shown. Where: x=5 ftShow your solution and round off if possible
Please show complete solution with complete FBD
1) Identify the Yield Strength of the material using a 0.2% Offset line
PROBLEM 3: Determine centroid of the composite figure. Refer your final answer to x and y axis. 3" 5" 12" 6" 4° ר 6' 下 5" 6"
Situation 5: The compound bar, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25°C. Assume that the walls do not yield and use the following data: A (mm²) a (/*C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segrnent 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10- 200 - 500 mm→- 400 mm- 800 mm Aluminum Steel Bronze 17. Compute the stress in the bronze bar a. 31.6 MPa (T) b. 31.6 MPа (С) 18. Compute the stress in the aluminum bar. а. 45.1 MPа (Т) b. 45.1 MPa (C) 19. Compute the stress in the steel bar. 79.0MPA (T) 79.0MPA (C) 13.6 MPa (T) 13.6 MPa (C) c. d. 54.1 MPа (Т) 54.1 MPa (C) с. d. a. C. 97.0 MPa (T) b. d. 97.0 MPa (C)
What is unconfined compressive strength test, which triaxial compression test is similar to shows? If the maximum compressive stress value obtained from this test is qu, this test Show the shear strength of the specimen using the Mohr tensile circle. Also, short Why is the unconfined compressive strength of the Comment on its use. I will understand better if you type the answers with the keyboard thank you.
Define Osterberg Load Cell.
Two wood boards, each 15 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 995 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 5.6 kN. Use a = 21 mm and b = 168 mm. d Glue b P P a Answer: d = i mm
Two wood boards, each 17 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 1045 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 6.2 kN. Use a = 26 mm and b = 208 mm. Glue b P P Answer: d= i mm
A beam has a class 3 web and a class 2 flange. When along the stress-strain diagram will it fail, and how? Remember how we define the classes. Make a sketch showing a W-section beam that hasfailedin this way. How can this be prevented?
There are 3 factors that may be the cause of the production error in the reinforced concrete element shown in the figure.