PROBLEM 1: Two spheres, one heavier and weighing12000 N and of diameter 1.2 m and the other lighter and weighing 4000 N, are tied with a rope and placed in seawater. The density of sea water is 1025 kg/m^3. It was found that the spheres floated vertically with the lighter sphere just under the water PROBLEM Osurface. Illustrate the problem before answering the following questions:

PROBLEM 1: Two spheres, one heavier and weighing12000 N and of diameter 1.2 m and the other lighter and weighing 4000 N, are tied with a rope and placed in seawater. The density of sea water is 1025 kg/m^3. It was found that the spheres floated vertically with the lighter sphere just under the water PROBLEM Osurface. Illustrate the problem before answering the following questions:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Proble A weight of 100 Ib is supported by two ropes as shown. Calculate the tension in each rope needed to keep the weight in this equilibrium position. 50° 75 8. FBD TCA Tca If the breaking tension of each rope cord is 120 lb, will the cords support the system as shown? Explain why or why not. Explain O Yes they will hold O No, something will break
If the weight of the crate is 2021 Newtons, calculate the tension in: Cable A in Newtons Cable B in Newtons Cable C in Newtons
1. The plate is horizontal, is in equlibrium, and weighs 1450 N. Determine the tension in cables AB, AC, and AD. Use Excel to solve the system of equations, and submit your Excel file (along with the pdf file of your solutions to these problems). 1.2m B AP 0.9m 0.9 m- C D 0.8 m 0.8 m
STRENGHT OF MATERIALS (Please write the solutions correctly and legibly. No long explanation needed. Answer in 3 decimal places. Rate will be given. 15 minutes left :<) Write the shear and moment equations for the beam loaded as shown and sketch the shear and moment diagrams. Indicate all values at the change of load points. Use a ruler for the stright line part/s of the diagrams.
A crate weighs 655 lb and is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the zy plane. Point A is located at a height of h = 48 in above the top of the crate directly over the geometric center of the top surface. Use the dimensions given in the table below to determine the tension in each of the three ropes. 2013 Michael Swanbom cc i❀O ↑Z CC BY NC SA a b с с 6 The tension in rope AC is 조 Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 44 in 35 in 12.1 in The tension in rope AB is The tension in rope AD is χ lb lb a lb D
A crate with a mass of 250 kg is held in equilibrium by three ropes attached to a steel ring. a d3 d₁ d5 B A 5.5 m 4 m d2 3.5 m 2m d₁ Z 3 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2 m d₂ d4 a. Determine the magnitude of the force/tension in cord A, TA. b. Determine the magnitude of the force/tension in cord B, TB. c. Determine the magnitude of the force/tension in cord C, Tc. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord A is The magnitude of the force/tension in cord B is The magnitude of the force/tension in cord C' is d5 kN kN kN
The rectangular plate (L,xL,) given below is installed between two rigid walls and is deformed as shown by dashed lines. Determine the shear strain y and Yxy at point A. Use the table given below and your student ID to find the values of L, L, a, and b. L2 A b. L. b L, (mm) (mm) (mm) 150 200.0 3.0 3.0
Four gears are attached to a circular shaft and transmit the torgues shown in the figure. The allowable shear stress in the shaft is 20,000 psi. 8000 lb-in. 19,000 lb-in. 4000 lb-in. A 7000 lb-in. B D (a) What is the required diameter d of the shaft (in inches) if it has a solid cross section? in. (b) What is the required outside diameter d (in inches) if the shaft is hollow with an inside diameter of 1.8 in.? in.
The shaft is supported by a journal bearing at A and a thrust bearing at B. (Figure 1) Figure -6 ft- 3000 lb 2500 lb 75 lb/ft I pontot, -12 ft 1 of 1 2 ft Part A Determine the normal force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B HÅ Submit Value Part C Request Answer Determine the shear force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Vc = Value μA Units Request Answer ? Units ? Review
Q\ a bridge beam, loaded in bending. The need it must be strong enough to carry, without breaking, the bending moment exerted by the people. Also, it must be as light as possible. Devise concepts to meet the need and sketch an embodiment
The prismatic rod shown is made of a steel that is assumed to be elastoplastic with E = 200 GPa and oy = 280 MPa. Knowing that couples M and M' of moment 525 N·m are applied and main- tained about axes parallel to the y axis, determine (a) the thick- ness of the elastic core, (b) the radius of curvature of the bar. y M 18 mm 24 mm X 'M'
Determine the components of the resultant force and the magnitude of the resultant.