PROBLEM 1 The platform scale consists of a combination of third and first class levers so that the load on one lever becomes the effort that moves the next lever. Through this arrangement, a small weight can balance a massive object. If a 3kg counterweight S is used to balance a 120kg load L, what is the value of 'x'? Draw all pertinent FBDS. Use g=9.806 m/s?. 100 mm 150 mm 250 mm H |E F G 150 mm - 350 mm- A

PROBLEM 1 The platform scale consists of a combination of third and first class levers so that the load on one lever becomes the effort that moves the next lever. Through this arrangement, a small weight can balance a massive object. If a 3kg counterweight S is used to balance a 120kg load L, what is the value of 'x'? Draw all pertinent FBDS. Use g=9.806 m/s?. 100 mm 150 mm 250 mm H |E F G 150 mm - 350 mm- A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Proble A weight of 100 Ib is supported by two ropes as shown. Calculate the tension in each rope needed to keep the weight in this equilibrium position. 50° 75 8. FBD TCA Tca If the breaking tension of each rope cord is 120 lb, will the cords support the system as shown? Explain why or why not. Explain O Yes they will hold O No, something will break
In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a clockwise moment of 340 lb in about point A. (Figure 1) Figure A == 18 in. 30° 5 in. 114 1 of 1 Part A Determine the required magnitude of force F. Express your answer with the appropriate units. μÅ F = Submit Value Provide Feedback Request Answer Units ?
A crate weighs 655 lb and is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the zy plane. Point A is located at a height of h = 48 in above the top of the crate directly over the geometric center of the top surface. Use the dimensions given in the table below to determine the tension in each of the three ropes. 2013 Michael Swanbom cc i❀O ↑Z CC BY NC SA a b с с 6 The tension in rope AC is 조 Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 44 in 35 in 12.1 in The tension in rope AB is The tension in rope AD is χ lb lb a lb D
A crate with a mass of 250 kg is held in equilibrium by three ropes attached to a steel ring. a d3 d₁ d5 B A 5.5 m 4 m d2 3.5 m 2m d₁ Z 3 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2 m d₂ d4 a. Determine the magnitude of the force/tension in cord A, TA. b. Determine the magnitude of the force/tension in cord B, TB. c. Determine the magnitude of the force/tension in cord C, Tc. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord A is The magnitude of the force/tension in cord B is The magnitude of the force/tension in cord C' is d5 kN kN kN
A tripod supports the load W as shown in the figure. Determine the maximum load "W" (in pounds), that can be supported by the tripod if the capacity of each leg is limited to 81 Ibs only. Round off to two decimal places. 2.4 m 1.8 1.8 0.90 1.8
Q1/ The weights of the various components of the truck are shown. Replace this system of forces by an equivalent resultant force and specify its location measured from B? Ans: R=- 10750 lb, d= 13.7 ft 3500 lb B 5500 lb) A 1750 lb tont -14 ft- 3 ft 2 ft ...
The 62-mm-diameter steel shaft is subjected to the torques shown. (Figure 1) Figure 1 of 1 400 mm B 3 kN.m 600 mm 2 kN-m I GILM Determine the angle of twist of end A with respect to C. Take G=75 GPa. Express your answer to three significant figures and include the appropriate units. A/C= Submit μA Value Units My Answers Give Up ?
C The beam shown in the given figure carries loads of 15 kN and 30 kN at points X and Y respectively and produces a deflection of 5 mm at point Z. X Y Z To produce deflection of 7 mm and 8 at X and Y respectively, then the load required at Z is 50 kN. The value of 8 will be
The shaft is supported by a journal bearing at A and a thrust bearing at B. (Figure 1) Figure -6 ft- 3000 lb 2500 lb 75 lb/ft I pontot, -12 ft 1 of 1 2 ft Part A Determine the normal force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B HÅ Submit Value Part C Request Answer Determine the shear force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Vc = Value μA Units Request Answer ? Units ? Review
09:05 A rectangular slab has 4 applied forces, but only F₂ and F3 are known. It is known that the resultant force FR acts through the x, y coordinates (12, 10)m. Variable F2 F3 d₁ d₂ F₁ = F₁ d3 d₁ d5 Value wamap.org Z 12 KN 6 KN 8 m 12 m 4 m 16 m 6m F2 Values for the figure are given in the following table. Note the figure may not be to scale. F3 F4 ) KN d5 y a. Determine the magnitude of the forces F₁ and F4 if the resultant force FR acts through the x, y coordinates (12, 10)m. Round your final answers to 3 significant digits/figures.
Solve the problem and answer the questions that follow. - If the supports were swapped such that the left support were a roller and the right support a pin, how would your solution change? - If the value of “w” were doubled, what would be the bending moment at the left most point of the beam?
Question 6 What will be the value of P in kN if below structure collapses in a purely sway mechanism? Round your answer to one decimal digit. Plastic moment for all members = 46 kN.m L = 4 m Round your answer to 1 decimal place. Shipping Tool с P→ B A L L D #F L P/₂ E