PROBLEM 1 For the given set of forces shown, determine the following if each side of the square is 1m in length.: a. the type of force system b. the magnitude of the couple c. the resultant moment of the forces about A d. the resultant force e. the perpendicular distance of the resultant force from A. f. the x and y intercepts of the resultant force with respect to the X and Y axes thru A.

Q: Why don't point B and D have a force in the y-direction?

A:

Q: What is the y component of a force with magnitude of 5kn applied 120 degrees with respect to the…

A:

Q: Resolve the horizontal 660lb force as per figure below into components acting along the u and vaxes…

A:

Q: Can you show how you got the moment for each Force from A?

A: Resolving the inclined forces F1 and F3 as shown in the figure.

Q: find the horizontal and vertical forces acting on the block in terms of Q

A: Given:-  To Find:-  horizontal and vertical forces acting on the block in terms of Q

Q: II. Find the reaction forces. A 9m 30 KN/m 25 KN/m 7m 15 KN-m 3m 5 KN 3m 3 m 9m 10 KN/m 10 KN/m 7m B

A: Given data, In a given beam, two traingular loads, two rectangular load, one point load and one…

Q: Q2/ Analy ze the forces shown in (Figure 2) into their components. F1 F2 F3 Figure 2

A: We have to figure out the horizontal and vertical components . for that we need to figure out the…

Q: Find forces A and B in diagram at right.

A:

Q: 4. Find the x-component and the y-component of the forces in 1200 Ib - of Frg. 2a -

A: We have to find x component and y component forces...for this we required to find forces in x and y…

Q: The pipe assembly is subjected to the 150-N force(Figure 1). Part A Determine the moment of this…

A:

Q: 03) For the concurrent coplanar korce system shown below, calculate the magnitude and the slope of…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: Q1: Find algebraically the resultant (R) and equilibrant (E) of the followinng coplaner forces: 300…

A: Solution is given below

Q: F- 10N 250 mm The 10-N force is applied to the handle of the hy- draulic control valve as shown.…

A: Solution: The Joint at B will have a Force F=10N and a moment due to this force will be acting on…

Q: Determine the resultant of the three forces acting on the pulley shown.

A: Consider the diagram as shown below for the resultant of the three forces.

Q: Find the component of the force F = -7i + 8j – 9k lb along the line through the origin making equal…

A: Given data: F = -7i + 8j – 9k Need to determine the component of the force.

Q: Q.4) For the figure shown compute the components x, y, and z of the 600- N force, also determine the…

A:

Q: 200 lb Use the force triangle method 3 ft- 3 ft and law of sines to find the the reactions at C and…

A:

Q: 10. If magnitude of two forces 6 , 8 and resultant of them is 2/13 N .then angle between two forces

A: Given, Magnitude of two forces,F1=6NF2=8NResultant of two forces,R=213 NTo determine,Angle between…

Q: For the figure below, determine the x and y components of the sum of the two forces

A:

Q: Find the resultant of the force system shown in fig. and located * ?w.r.t. point O 3kN 30 0.1 m 0.1…

A:

Q: Problem 2 It is desired to replace the 560 N force R acting on particle A with two forces P and Q…

A: As per our guidelines we are supposed to answer only one question. To find: The other component…

Q: 2. Determine the moment of the four forces acting on the rod as in the fig. about point 'o' 40 N N…

A: The free body diagram for the body is given below,

Q: Four parallel forces act on the plate as shown. For the force system shown, find the equivalent…

A:

Q: Find the resultant force of the following? B, 2 m 3.5 m F-600 N 0.5 m Fe 450 N 1.5 m 0.5 m 1.5 m

A: Given Data: The force FB=600 N The force FC =450 N. The coordinate of point A is (0.5,-1.5,0) The…

Q: 3- Determine the force T and C 3 kN 20 16 kN 40 8 kN

A: In horizontal direction    Tcos40+8+Csin20-16=00.766T+0.342C=8         -1

Q: 4. Find: the x and y Shown below. components cf each force prce

A:

Q: Easy Problem: Determine P and Q so that the their resultant force R are equivalent to a single 2000…

A:

Q: 3- Determine the force T and C 3 kN 20 16 kN 40 8 kN

A: Data given- Need to determine T & C

Q: The force that replaces the entire system of forces and gives the same effect as that of the system…

A: The force that replaces the entire system of forces:

Q: Problem 3. What is the moment of the 1.4 kN force along the direction of the 1.0 kN force? Express…

A: All the dimensions are shown in the figure.For finding the moment of the 1.4 KN along the 1 KN axis,…

Q: A FBD should include the isolated system and only the known forcesand moments. O O O false true

A: To select the correct option.

Q: Q3: Find the moment a bout at point A 100mm 100mm 200N 150N 45 200mm 15N.m 40N.m 80N

A: Given data: -  The force at extreme right side is F1 = 150 N. The force at extreme left side is F2…

Q: 1)The three forces in figure create a vertical resultant acting through point A. if T is known to be…

A:

Q: Easy Problem: Determine P and Q so that the their resultant force R are equivalent to a single 2000…

A:

Q: Draw FBD m 2 of above condition

A:

Q: Q3/Replace the 200 N force in fig. shown by a force which passes through A and a couple whose forces…

A: Given data: Applied force = 200 N Need to determine the force at point a and couple.

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.