Problem 1: For the given cantilevered beam section shown below check the4 section for shear and design for shear reinforcement if required. Draw the stirrups distribution. if fc = 4 ksi, fy = 60 ksi, normal weight concrete, choose #4 for stirrups. d=23" W₁ =3k/ft WD =2k/ft ▼ 10" #47 2" 4-#8 12" 5" 20"

Problem 1: For the given cantilevered beam section shown below check the4 section for shear and design for shear reinforcement if required. Draw the stirrups distribution. if fc = 4 ksi, fy = 60 ksi, normal weight concrete, choose #4 for stirrups. d=23" W₁ =3k/ft WD =2k/ft ▼ 10" #47 2" 4-#8 12" 5" 20"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bracket with bw = 350 mm and h = 450 %3D mm protruding from a beam column is subjected to a reaction force RD = 140 kN by a fixed load in a vertical direction at a = 180 mm position and a reaction force RL = 160 kN by a loading load. Additionally, fck = 28 MPa and fyt = 400 MPa are placed integrally with normal weight concrete. Design the bracket using these conditions.
Determine the additional longitudinal reinforcements (mm2) due to torsion of a rectangular beam with a width of 469 mm and an over-all depth of 632 mm. It is subjected to a factored torsion of 110 kN-m. The specified compressive strength of concrete is 21.70 MPa. The yield strength of tension reinforcements and stirrups are 348 MPa and 278 MPa respectively. Use 12 mm stirrups. Round off only on your final answer (3 decimal places).
Subject reinforced concrete design please solve part C and D
Question Discuss the Plastic Hinge Length for this :- O simply supparted with concentrated Lead. simply supparted with uniform Load. O Simply supprted with two concentrated Load 4 Cantliver beam with cancentrated Lead at,end. Free Cantliver bea with distributed Load. you Can use wusw.concrete.org> SP_12 this salution to Find subject/Advanced Concrete Design Dear, flease help me to find solution far it question. un 部 odd case(4) Case Q) P case(3) Case (4) A case(5) distributed load (u)
Given the concrete (f c=6000 psi) I-beam shown in Figure 1 for the given loading: -draw the shear & moment diagrams -determine Vmax & Mmax -using ASD (Allowable Stress Design) method, check to see if the given loading produces stresses within the given allowable range (check both Omax & Vmax) Using ACI 318-99, allowable stresses are -for flexure, f = .45f'c -for shear, v. = 1.1√f. (HINTS: 8² -note that the beam is symmetric about both axes -Ix for a triangle is (1/36)bh³+Ad² ) 30 kips 16' 10 kip/ft 22' 20 kips 3'-4' -1-6 -1'-6" Figure 1 1'-
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
A beam has a width of 280 mm and 490 mm overall depth. Concrete cover is 65 mm from the centroid of bars. Concrete compressive fc' = 24 MPa. Steel yield strength are fy=415 MPa and fy = 275 MPa for ties. Determine the shear strength provided by concrete using simplified method a) If the beam is subjected to shear and flexure only, and b) If the beam is subjected to axial compressive force of 124kN.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
STRUCTURAL THEORY: USING PORTAL METHOD. Detailed computation. please
If the given beam section is used for a simply supported beam 5.0 m span, using fc = 21 MPa and fyt = 280 MPa: 10-mm-dia 425 mm @ 200 mm 500 mm -275 mm 75 mm 25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. = kN 26. Calculate the nominal shear strength of the stirrups, Vg = kN. 27. Calculate the design sectional shear strength of the beam = kN 28. Determine the maximum factored uniform load in that can be sustained based on shear strength of the cross-section only. = kN/m 29. Determine the maximum live load in that can be sustained based on shear strength of the cross-section only. = kN/m 30. If the total factored uniform load is 60 kN/m, calculate the ultimate shear force at critical section for shear in kN. = kN INPUT ALL ANSWERS ROUNDED TO WHOLE NUMBER
1. A rectangular beam section is 10 in. wide and has a structural depth of 13.5 in. Reinforcement consists of two No. 8 bars. Given that the strength normalweight concrete is 4000 psi and there is NO shear reinforcement in the section, determine the nominal shear capacity allowed by the ACI Code. (5 pt) (Hint: No web reinforcement, so Vc = 8λ¸λ(pw)¹/³¸ √ Fcbw d cbwd shall be used).
Correct solution