Problem (1): A solar cell has an open circuit voltage value of 0.60 V with a reverse saturation current density of Jo = 3.9 x 10° A/m2.The temperature of the cell is 27°C, the cell voltage is 0.52V, and the cell area is 28 m?. If the solar irradiation is 485W/m², determine the power output and the efficiency of the solar cell.

Problem (1): A solar cell has an open circuit voltage value of 0.60 V with a reverse saturation current density of Jo = 3.9 x 10° A/m2.The temperature of the cell is 27°C, the cell voltage is 0.52V, and the cell area is 28 m?. If the solar irradiation is 485W/m², determine the power output and the efficiency of the solar cell.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

solve in less than 30 min pls . pls.
1.what are your comments on the future R&D directions for further improvement of NMH batteries? 2. Based on your understanding, please draw your own version of diagram to show the basic mechanism of NiMH battery. Please clearly indicate the direction of charge and discharge in your diagram. 3.What are the requirements for negative electrode hydride materials?
If the operating voltage of the LED diode given in the circuit in the figure is 2.2V, the operating current is 30mA, and the Vs source voltage is 12V, calculate the value of the R1 resistor connected in series with the diode.
Fundamentals of Electric Circuits.
For the circuit shown in Figure 2 let Vcc=5 V, R₂ = 4 k2, R₂ = 3 k2, R₁ = 60 k2, and R₂ = 40 k2. The transistor parameters are ß= 50 and V₁ = 80 V. (a) Determine Ico and VECO- (b) Plot the dc and ac load lines. (c) Determine A,= vo/v, and 4, = io/is. (d) Determine Rb and R.. Vcc R₂ R₁ Figure 2 V₂ Ca Rib 201 RE Cc2 -0% RL
Figure Q4 shows the silicon wafer. This silicon has been added with the two elements as listed in Table Q3. Identify the majority charge carrier in each extrinsic silicon wafer and justify your answer with illustrations.
Compare the dependence on temperature for electrical conductivity in metals and semiconductors intrinsic, explaining the difference in behavior.
A 1.5 V battery is added to the photoelectric effect apparatus as shown below. Monochromatic light source Evacuated tube + 1.5 V B Make a sketch of the above circuit and label electrodes A and B according to the type of charge (+ or -) that accumulates (whether the light is on or off). When the light is turned on consider the following questions: • Is the number of electrons emitted from electrode Beach second when there is a battery in the circuit greater than, less than. or equal to the number emitted each second when there is no battery? Explain. • What is the potential difference across the electrodes (AV = VA - VB)? • What does your answer to the above question imply about whether the net charge on each of the electrodes changes? Explain. • Write an expression relating the potential difference AV to the change in kinetic energy of a single electron as it moves from electrode B to electrode A. (Hint: Consider the work done by the electric field between the electrodes or the…
Q2. An ideal single phase source 240V, 50HZ, supplies power to resistive load R=10 Q via a single ideal diode. Calculate the average and root mean square values of the current. What must be the rating of the diode?
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm