Problem #1A de-de converter produces 5V output with 2% line regulation and zero load regulation. The outputleads connected to the load have a resistance of 4x10-32. Determine the worst-case minimum andmaximum expected voltage at the load terminals for operation over full allowed input voltage rangeand a load variation over a range of 10W to 100W.

The given information is written below.Output voltage is Volts.Line regulation is Load regulation…

Problem #1 A de-de converter produces 5V output with 2% line regulation and zero load regulation. The output leads connected to the load have a resistance of 4x10-302. Determine the worst-case minimum and maximum expected voltage at the load terminals for operation over full allowed input voltage range and a load variation over a range of 10W to 100W.

Problem #1 A de-de converter produces 5V output with 2% line regulation and zero load regulation. The output leads connected to the load have a resistance of 4x10-302. Determine the worst-case minimum and maximum expected voltage at the load terminals for operation over full allowed input voltage range and a load variation over a range of 10W to 100W.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A stabilization circuit has a stability factor of 0.04 and an internal resistance of 5 2. The unstabilized voltage can vary between 75 and 100 V, and the load current can vary from 40 to 80 mA. Determine the maximum and minimum values for the stabilized load voltage.
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di i v2 = VmSin ot RL Vs(N V1 Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V None of the above ell ell
For the buck-boost converter, determine the duty cycle, the switching frequency, and the inductor current ripple. The output voltage ripple is about 1%. vs 10 V, mH, C 0.5 micro.F, Vout=-20 V, R-IO Q
A balanced 3-0 star connected load is fed from a 350 V, 3-p supply. Each load has resistance of 35 Q. The total Active power is Select one: O a. 1.15Kw O b. 3500KW O C. 12KW O d. 3.5Kw
Question 11 In a step-up/step-down converter, Vin=12V, Vioad=15V (regulated), Itoad=250mA, Lmin = 150µH, C = 470µF and fs=20kHz. Calculate the peak-to-peak ripple of the load voltage.
A buck-boost converter operates with an input battery. It converts +12 V to –12 V at apower level of about 75 W. the switching frequency is 120 kHz. The switches have200 ns switching time. The battery has an internal series resistance of 0.2  and seriesinductance of 200 nH. (a) What is the operating value of the duty ratio? What power is lost in the battery resistance? (b) Propose an interface structure to improve operation and decrease losses. What are the duty ratio and battery resistance loss with your interface in place?
A boost converter is operated from a source voltage of 100V with a duty ratio of 0.4. The load resistance is 4000. The internal resistance of inductor is 0.40, then the average output voltage is
9- Buck type DC-DC converter, if the input voltage is 789 V and the occupancy-backlash ratio is 0.9, which of the following options is the correct load voltage. a) 710.1 etc) None c) O 7101 V d) O 78.9 V
For Steady-State Operation o f Boost DC-DC Converter What is the duty ratio (D) How can it effects on the converter output (Vo)
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
The initial delay of 30 degree replaced by 20 degree, in three phase half wave controlled converter with RL load, if T2 is triggered at 200 degree, what may be the firing angle of the converter? a. 120 degree b. 60 degree O c. 20 degree O d. 80 degree
For a buck converter, the following specifications are given: Vin = 600 V, L = 10 mH, and R =1 Q. a) Calculate the duty cycle required to deliver 200 A de into the load. b) Derive an expression for the peak-to-peak current ripple seen by the load. c) Estimate the switching frequency necessary to limit the peak-to-peak current ripple to no more than 5 A.