Problem 1: A converging-diverging nozzle is attached to a large reservoir of compressed air. The reservoir stores the compressed air at an absolute pressure of 400 kPa and a temperature of 30°C. The nozzle has a throat diameter of 50 mm. Determine the mass flow rate through the nozzle. You may assume k = 1.4 and R = 287 J/(kg*K) for air. O 50 mm 3 m L= 4 m Ø25 mm 30

Problem 1: A converging-diverging nozzle is attached to a large reservoir of compressed air. The reservoir stores the compressed air at an absolute pressure of 400 kPa and a temperature of 30°C. The nozzle has a throat diameter of 50 mm. Determine the mass flow rate through the nozzle. You may assume k = 1.4 and R = 287 J/(kg*K) for air. O 50 mm 3 m L= 4 m Ø25 mm 30

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Civil The height of a liquid column of mercury open to the atmosphere is 2.493 ft. Calculate the absolute pressure at the base of the column 1B_{t} / f * t ^ 2 psia, mm Hg. and in H-O. Assume that the density of mercury is 848.7 lb/ft and atmospheric pressure is 2116 lb/ft² absolute.
Q03
Use the following given values to solve problems, unless otherwise stated. Ywater = 9790 N/m³ = 62.4 lbf/ft°; g = 9.81 m/s? = 32.2 ft/s²; 1 hp = 550 lbf-ft/s = 746 Watts Problem-1 Water is pumped from the large tank through a uniform diameter pipe (d = 3 in.) and exits as a free jet (refer figure-a). The plot of the flowrate (Q) versus pump-head (hp) is a straight-line graph that passes through points (3, 16) as shown in figure-b. If the pipe friction head loss is, hf = 7V:/2g, where V is the average fluid velocity in the pipe, find a) the equation that relates hp and Q; b) flowrate and c) If the pump is 75% efficient, what horsepower is needed to drive it? Assume steady, incompressible flow. Ignore kinetic energy correction factor (a). 12 ft Pump %3D (a) 16 3. Q, ft°ls (b) dy
Please show step by step solution.
8. Compute the probable density of a fluid inside a floating spherical balloon having a 2m diameterif the tension in the balloon’s tie rope is observed to be 2kgf. Assume that the density of air is1.18kg/m3. a. 0.7225kg/m3 b. 0.6225kg/m3 c. 0.7025kg/m3 d. 0.5848kg/m3
The Venturi meter shown in the sketch below, contracts the flow down to one quarter of its original area. Cold air at 0 deg C flows in the pipe through the Venturi meter. The velocity of the air upstream of the Venturi meter is equal to 40 ft/s and the pressure at the same point is equal to 30 psia. What is the manometer reading if the fluid of the manometer is water with density 1000 kg/m3 . Assume that the air behaves as an ideal gas with molecular weight equal to Mw=29 kg/kmol and constant density evaluated at upstream conditions. Use Bernoulli's equation for your calculations. please respond asap!
In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height of column H is equal to Patm H 424 Hg:
1. The compressed air tank has a volume of 0.4 m. The temperature is 25°C and the atmospheric pressure is 101.35 kPa. When the tank is filled with air at a gage pressure of 262.74 kPa, determine the density of the air and the weight of air in the tank. Hint: Ideal gas law should be used. R-28 m/s?K
A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.83 mm. The nozzle shoots out water moving at 25.0 m/s. 1. Required information At what speed is the water in the hose moving? cm/s Required information What is the mass flow rate? g/s 2.
Not sure how to do this one. Would appreciate a full solution, thanks!
Water is flowing in a fire hose with a velocity of 1.0 m/s and a pressure of 200000 Pa. At the nozzle the pressure decreases to atmospheric pressure (101300 Pa), there is no change in height. Use the Bernoulli equation to calculate the velocity of the water exiting the nozzle.
Q4: A 7-cm diameter solid aluminum ball (SG = 2.7) and a solid brass ball (SG-8.5) balance nicely when submerged in a fluid as shown in figure. a) If the fluid is water, what is the diameter of the brass ball? b) If the brass ball has a diameter of 3.8 cm, what is the density of the fluid? 2 pulleys Fluid brass aluminum D= 7 cm +