PROBLEM 07: The figure shows a truss and the sequence of assembly of members at pins H, G, and F. All members of the truss have cross-sectional areas of 250mm2 and all pins have diameters of 15mm. Determine the following: a. Axial stresses in members HA, HB, HG, and HC. b. The maximum shear stress in pin H. H HC CF A 130° E 30 D -3 m---3 m→-3 m→-3 m ¥3 kN C GH ¥4 kN Ý2 kN Pin H Pin G Pin F

Q: How is ThOD solved?

A: THOD  Theoretical oxygen demand (ThOD) is the calculated amount of oxygen required to oxidize a…

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: What is this called?

A: Chisel

Q: F & H are incorrect

A: As per question requirment we only find out f and h here. Find out -  (f) Length of Curve (h)…

Q: Find the shortest distance from point B to line AC

A:

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: 1. GIVEN: REQOIREO: yo l0". 7,9 to locete the centreid t 6"

A: To find centroid

Q: Determine the centroid of the / ?figure presented in below 1.8 1n 1m1 2m 3m 2 2m 1m 0.5m X >X

A:

Q: Determine y for the area shown y 1" 1" in .5" 1" 2" 2" X

A:

Q: From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the centroid, (C),…

A:

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A:

Q: why divide x' in 2 in above method?

A: ##Calculation of location of x at such that due to given loading a  Maximum BM occurs ### As ask…

Q: what are the USCS group name for each of the four gradations

A: Given: Specimen LL PL PI Cc Cu 1 53 24 29     2       1.05 95.52 3 27 16 11 3.06 28.34 4…

Q: Is sigma xy horizontal and sigma xz vertical

A: Reference: wikimedia commons

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: 1) Determine the area of the shape below. -130.0- 100.0 -160.0-

A: The above figure is the trapezoid  The area of the trapezoid = sum of the parallel…

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: hat about pin d?

A: We know that Forces acting at Joint D are shown in figure below Forces moving away from joints are…

Q: Explain any fiften (15) AUTOCAD commands used in drawing

A: Autocad is a computer based drawing software which is in the field of civil engineering to prepare…

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: Differentiate initial and boundary value problems.

A: Both type of problems are similar to each other except for that boundary value problem have…

Q: نقطتان )2( Shows polygon with the followng :Find the area (x,y) 2 1.8 1.6- 1.4- 1.2 0.8 0.6- 0.4…

A: answer is option a.)   Matlab command window picture is attached below

Q: The representation of the hinge lines of the glass box in a drawing are known as lines. ....** .....…

A: The glass box concept is used in orthographic projection. When the glass box is visualized, then…

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: 2xyy' = y^2 -2x^3

A: Given data: Differential equa 2xyy'=y2-2x3

Q: 9. Using cantilever method, determine the maximum absolute axial force in the column in kN due to…

A: Given data in question  Lateral loading Dimensions  Cantiler method  To find out  Axial forces in…

Q: Fullform of CASBEE

A: CASBEE has been designed to both enhance the quality of people's lives and to reduce the life-cycle…

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 4)…

A: 1. Deactivate the voltage source (V1):Set the voltage source V1 to zero (0 V). This means the…

Q: Figure 2. Inside perimeter Outside perimeter Centreline

A: Inside perimeter :Length×2+Breadth×2+2×2'+3'24'3''×2+12'×2+2×2'+3'=79'6''

Q: -0129 -077 R26

A:

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: where did 3sqrt of 2 came from?

A: Given, A structure with carrying varying load   To find : Where 32 came from.

Q: what about CB, IH, AB & AB

A: To find zero force members.

Q: 4 cm 0 2 י 5 cm 4 567 Value: cm 10 5 150 Value: mm 0 140

A: There are two scales, and the values shown on the two scales are required.One is the main scale and…

Q: The block of mass m1 = m0 is attached to a spring of elastic constant k = (m0g)/H and natural length…

A:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.