Problem . .A member ABCD is subjected to point loads P, P, P, andPas shown in Fig. 1.11. B A P, P2 P. 2 625 mm 1250 mm 120 cm 60 cm -- 90 cm Fig. 1.11 Calculate the force P, necessary for equilibrium, if P, = 45 kN, P, = 450 kN and %3D P4 = 130 kN. Determine the total elongation of the member, assuming the modulus of elas- ticity to be 2.1 x 105 N/mm². 2500 mm

Problem . .A member ABCD is subjected to point loads P, P, P, andPas shown in Fig. 1.11. B A P, P2 P. 2 625 mm 1250 mm 120 cm 60 cm -- 90 cm Fig. 1.11 Calculate the force P, necessary for equilibrium, if P, = 45 kN, P, = 450 kN and %3D P4 = 130 kN. Determine the total elongation of the member, assuming the modulus of elas- ticity to be 2.1 x 105 N/mm². 2500 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the figure below, a weight W is suspended from point D of a beam AD. The beam is held up by rod BC. Neglect the mass of the beam AD and rod BC. Which of the following is true (select all that apply). Beam AD is a three force member The direction of the force in rod BC (i.e whether the force is tension or compression) is known Beam AD is a two-force member Rod BC is a two-force member 4m 4m The line of action of the force in rod BC is known The magnitude of the force in rod BC is known 3m B D W
Bar AB of Fig. with weight W and length L has a uniform cross section. Rotation of the bar is resisted by a torsional spring with spring constant 4. The spring is neutral when 0- 0°. Determine The minimum stiffness & for the spring, in terms of W and L, if the bar is to be in stable equilibrium when 0 = 0°.
A 27‑kg sing is attached to the right end of a horizontal beam (the beam's mass m = 7.7 kg). The left end of the beam is mounted into a wall and it's right end is supported by a string which makes an angle θ = 32° with the beam, see the picture below. Find the magnitude of the tension in the string. 1. The tension in the string, T Find the reaction force exerted by the wall on the beam. 2. The x component of the wall's reaction force, Rx = 3. The y component of the wall's reaction force, Ry =
Two weights, A and C, are fixed to a bar, B. Their masses are: A = 60 kg, B = 230 kg,C = 45 kg. B is, in turn, connected to a fixed vertical post by a hinge and a support cableD. The geometry of the system is shown at right. Treat weights A and C as point masses a)What is the tension in support cable D? Be sure to include a detailed freebody diagram to accompany your analysis.b) What is the magnitude of the force provided by the hinge?c) What is the moment of inertia of the A + B + C as a rigid system, for rotationabout the hinge? For analysis, break the beam into a short piece to the left of thehinge, and a separate longer piece to the right of the hinge. If the support cable D on should break,d) what is the angular acceleration of the beam and weights at the moment the cable breaks?e) what is the magnitude of the linear acceleration experienced by each of the weights, A and C, at moment the cable breaks?
A square body of side L-1 with one vertex on origin is in static equilibrium. It is subjected to body force per -axi - ayj, a unit area as , a = 1. The sides AB and BC are traction free whereas traction is uniform on the sides AB and AD with magnitudes qAB and qAD, with direction as shown. What are the values of qAB= and and QAD ? What are the values of ox= Oxy problem] 9AD D == Traction free с qAB Traction free B at point with coordinates x = y = [Assume no shear forces for this
Fig. 1 shows a simple six bar linkage held in static equilibrium while a torque Tin = 250 N mm is applied. Determine the reaction forces at each joint and the holding force P by considering the free-body diagrams of each member. Each small square on the grid is 50 mm by 50 mm. H E Figure 1 Simple Six Bar Linkage B Tin
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 17i - 11j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. %3D 2 m 4 m 6 m A Answer: Calculate the magnitude of the tension in cable BD in kN. 3 m 6m
Q.1) For the roller support at and pin support at B, Compute the reactions at A and B. B Answer: 40 N 50 N 30 N 10N B = 6 cm 6 cm 10 cm 8 cm Q.2) Find the tension in each wire A, B and C supported a plate weighs 56 N as shown in figure. 10 cm 16 cm 4 cm 10 cm TA = TR = 16 cm
Question 1. RAX A 0 RAY F₁ Enter FAP: KN F KN E F₂ D The figure above is a pin-joint frame with angle 8 = 50° between members AF and AB. (Note that the diagram is not to scale). Given that the reaction forces at the support A are given by RAx = 70kN and RAY = 30kN, calculate the forces in members AB and AF, denoted by FAB and FAF respectively. Enter your answers in kilonewtons (kN) correct to 2 decimal places in the boxes below: Enter FAB RDY 4 [6 m
Asap
Help me
Questian Determine the horizontal and veliu force in the bar BD of the structure given in Figure 2. DP 3 m 200 N 80 N/m 4 m 2 m Figure 2 Question 3: (4.0/10) Give the truss structure as shown in Figure 3. a. Determine the horizontal and vertical components of reaction at A and E. b. Determine the internal forces in the bar AB and BH of the truss structure. 20 kN 40 kN 40 kN 40 kN 20 kN 8 kN F H 6 kN 2 m E- 2m* 2 m k 2 m* 2m Figure 3