Prob.2. The following observations were recorded during á test on a single cylinder oil engine – Bore = 300 mm, stroke = 450 mm, speed = 300 r.p.m., i.m.e.p. = 6 bar, net brake load = 1.5 kN, brake drum diameter diameter = 2 cm. %3D %3D 1.8 metres, brake rope %3D |3D Calculate – (i) Indicated power (ii) Brake power

Prob.2. The following observations were recorded during á test on a single cylinder oil engine – Bore = 300 mm, stroke = 450 mm, speed = 300 r.p.m., i.m.e.p. = 6 bar, net brake load = 1.5 kN, brake drum diameter diameter = 2 cm. %3D %3D 1.8 metres, brake rope %3D |3D Calculate – (i) Indicated power (ii) Brake power

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For base case: N= 3500 rpm. D = 8 and 3/8 inch, Q = 400gpm, H = 280 ft, P = 41 hp, %3D Determine new Q. H, and P for |(a) when diameter is changed to 7" and speed is constant (b) when speed changes to 1750 rpm and diameter is constant (base case diameter)
Q108 The fallowing data refers to a test ona single cylinder four stroke oil engine Cylinder bore 220mm; stroke 360mm; area of indicator diagram 360mm length af diagram 40mm; indicator Spring rating =1.25 mm/bar; Speed 300 rev/min brake load 441-3N at o.9m radius; fuel consumption 3.8 Kg/hr} Calorific Value of fuel 43124 kj/kg ; Cooling water flow 3.8kg/hrjrise intemperature of coaling water 48K;and specific heat capacity of water 4.1868 Kj|Kg.K 340d.13biliN Calculate: @ the mechanical efficiency the indicated thermal efficiencyui a The heat balance sheet expressed as ki/min andas percentage of the heat supplied to the engine.
A six-cylinder two-stroke automotive engine has been designed to provide a maximum brake torque of (3.30x10^2) Nm at rated engine speed of (5.000x10^3) rpm. The engine specifications are listed below: Bore and stroke (mm): (8.4000x10^1) x (9.2000x10^1) Compression ratio: 11.0: 1 Find its brake mean effective pressure (bmep). The answer should be in kPa with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer
What thrust is obtained from a propeller 3 m in diameter that has the characteristics given in Fig. 14.2 when the propeller is operated at an angular speed of 1400 rpm and an advance velocity of zero? Assume 1.05 kg m3
During a test on a five-cylinder four-stroke IC diesel engine with a cylinder bore and stroke length of 260 mm and 305 mm respectively, running at 503 r/min, the following results were obtained: Mass on Dynamometer mass hanger (arm length = 0.825 m) 221.9 kg Indicated mean effective pressure 400 kPa Fuel consumption (with Qnet,v = 39.8 MJ/kg, density = 0.944 kg/l) 6 ml/s Take acceleration due to gravity as 9.81 m per square seconds Calculate the brake power .
During a test on a 3-cylinder four-stroke IC diesel engine with a cylinder bore and stroke length of 276 mm and 306 mm respectively, running at 547 r/min, the following results were obtained: Mass on Dynamometer mass hanger (arm length = 0.815 m) 200.6 kg Indicated mean effective pressure 428 kPa Fuel consumption (with Qnet.v = 39.8 MJ/kg, density = 0.944 kg/l) 6 ml/s Take acceleration due to gravity as 9.81 m per square seconds Calculate the mechanical efficiency in decimal fraction to 3 decimal places, No unit needed for answer
A four-stroke, 12-cylinder diesel engine has a bore and stroke of 820 mm and 2020 mm, respectively, per cylinder. The brake mean effective pressure of each cylinder is 1.2 MPa and the engine rotates at 145 rpm. The brake thermal efficiency of the engine is 32%, the mechanical efficiency is 72% and the net calorific value of the diesel is 40.75 MJ/kg. 1. calculate the specific fuel consumption (kg/kWh) ? Answer to 3 decimal places. 2. calculate thefuel consumption (kg/h) ? Answer to 0 decimal place.
Do please
CTION A estion 1 A double acting cylinder is used to raise and lower a 150 kg mass attached at the end of a steel cable as shown in Fig. 1(a). Answer each of the following: (0) If the cylinder is supplied with compressed air at 6 Bar, calculate the standard cylinder diameter required. (i) What is the optimal method of speed control for lowering this mass? Explain your answer, m=150 kg Fig. 1(a)
A four-stroke automotive engine has been designed to provide a maximum brake torque of (2.00x10^2) Nm at rated engine speed of (4.8000x10^3) rpm. The engine specifications are listed below: Bore and stroke (mm): (7.900x10^1) x (8.300x10^1) Compression ratio: 12.0 : 1 Estimate the maximum brake power the engine will deliver. The answer should be in kW with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10
E1. A full journal bearing has the following specifications: Journal Diameter:46 mm Bearing length: 66 mm Radial clearance to radius ratio: 0.0015 speed : 2800 r/min Radial load: 820 N. Viscosity of the lubricant at the operating temperature:8.4 cP Considering the bearing as a lightly loaded bearing, Determine (a) the friction torque (b) Coefficient of friction under given operating conditions and (c) power loss in the bearing.