Pressure regulators are being discussed. Technician A says they are located in the fuel rail. Technician B says they are located on the fuel rail. Who is correct?   a. A only     b. B only     c. Both A and B     d. Neither A nor B

Q: The firing lines on an oscilloscope pattern are all abnormally low. Technician A says that the…

A: Solution:

Q: C.Both A and B

A: The main objective of Central port fuel injection system is to a low cost multi point fuel injection…

Q: While discussing fuel boiling in the fuel rail: Technician A says that fuel boiling in the fuel rail…

A: Fuel rails are used in multi-point fuel injection systems. It is basically a pipe or two connected…

Q: injector cleaning is being discussed. technician A uses a wire brush to clean the tips of the…

A: Solution:

Q: Technician A says check balls are often used to block holes between the transmission valve body and…

A: pacer plates are also commonly used in automatic transmissions to provide additional clearance…

Q: Technician A says that black exhaust smoke is an indication of a too-rich air-fuel mixture.…

A: Air–fuel ratio is defined as the mass ratio of air to fuel present during combustion. Rich air-fuel…

Q: Explain the two main dangers from oxygen cylinders and what causes them. b) Why is cleanliness very…

A: Hazards from oxygenOxygen gas in cylinders is used by many people at work and sometimes at home.It…

Q: A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and the cooling…

A: Given :-  A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and…

Q: Two techs are discussing oil coolers. Technician A says that when inspecting oil- to-water type…

A: Solution:

Q: explain the function of the pressure relief valve within the engine oil pump.

A: To explain: The function of pressure relief valve in engine oil pump need

Q: Most fuel tank filler caps contain a pressure valva and a

A: Fuel tank filler caps are used to seal the fuel tank opening which is used to refill the tank. They…

Q: 24: Where are the following parts located? - Integral fuel tank a. Horizontal stabilizer b. Rudder…

A: 1) The NACA vent2) The rigid removal fuel tank3) Bladder fuel cell

Q: For a hydraulic power unit, this part indicates the amount of oil in the reservoir. Usually, it also…

A: This question is based on the concept of Hydraulic power unit

Q: While discussing the different types of pressureplates: Technician A says that coil spring types…

A: Option D is the correct naswer

Q: An overheating vehicle is being discussed. Technician A states that the vehicle may be overheating…

A: Given Data: An overheating vehicle is being discussed. Technician A states that the vehicle may be…

Q: While discussing electric fuel pumps: Technician A says that some electric fuel pumps are combined…

A: "Technician A only"   Given information: While discussing electric fuel pumps: Technician A…

Q: Technician A says that it takes about 1 pint of oil to raise the oil level from "add" to "full."…

A: Technician A says that is takes about 1 pint of oil to raise the oil level from "add" to "full".…

Q: Technician A says that an air-conditioning system removes heat from inside the engine. Technician B…

A: Technician A says that an air-conditioning system removes heat from inside the engine. Technician B…

Q: an engine is being discussed for lean running condition. technician A checks for air leak in the…

A: There are five factors that causes to run engine in lean condition. They are Fuel System Oxygen…

Q: the oil pressure light stay on whatever the engine fis running, and the oil pressure has been…

A: Oil pressure light indicates that the pressure of the oil is within the specified limits. It will…

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.