Prepare a schedule of bars for the R.C.C. Lintel shown in the fig. 4-²

Q: H.W3: Draw I.L for RA, RC, RF, VB, VCL, VCR, VD, MA, MC, MD B D F 4m 2m 2m 3m 5m

A:

Q: There is a statically indeterminate beam in which the horizontal force at the left and right ends…

A:

Q: There is a sta at the left and force is show The flexural s

A: Ds = De + Di = 5-2-1 = 2                         it is indeterminate with 2 but RA & RB given…

Q: Draw SFD and BMD asap , pls

A:

Q: The following structure has pin reactions are given.

A:

Q: Please solev this structural engineering problem. WIll give 5 star rating and an upvote. Please…

A: Step 1:

Q: Olim 5x+ 2 4x2-1

A:

Q: (A 30' 5 EQUAL SACES 35 BEauAL SICES Ga I- 30 8. GI ca 30 -I- O FLOOR FRAMING PLAN uestions: O Dran…

A:

Q: In the reinforced beam section shown in the figure (not drawn to scale), the nominal cover provided…

A: Given Data: Consider that all dimensions are in mm. The width of the cover is 50 mm. The diameter of…

Q: 3D5x3 -10x-V3 5(х-2) %3D 1/3

A: Simple calculation taking commons

Q: Define the distance between the adjacent faces of the stock rail and the check rail , is called

A: The stock rail in the railway track are the main rails which are fixed. In the turnout the stock…

Q: Note: Concrete clear cover is 75mm. Hook end length is 125mm. Along X Along Y REINFORCEMENT DEPTH…

A:

Q: Problem No. 1.: All bars in the truss shown are 25-mm diameter steel rods (E = 200 GPa). SET P1, kN…

A:

Q: What part of the connection shown does not comply with NSCP 2015 Section 510.3.3, 510.3.4 and…

A: Given data-

Q: Problem No. 1.: All bars in the truss shown are 25-mm diameter steel rods (E = 200 GPa). %3D P1, kN…

A:

Q: Where is the centroid of the rectangular gate (typically represented by h)? 2 m below A 3 m below C…

A:

Q: 1.Determine V&M equations and diagrams 300 lb 80 Ib/ft A ID to TB 4 + 8' 6' Ay Су Shear diagram

A:

Q: Which of the following diameter of Grade 60 reinforcing bar can withstand a tensile load of 210,000…

A:

Q: Problem 2 Find the loading for the floor beams B-1 through B-5, and G-3 through G-5 of Problem 2 of…

A: A floor beam is a huge pillar, normally steel, that traverses the width of a house at the middle and…

Q: Determine the net area for the plate PL // x9 with 3/4 in bolts indicate which area controls

A: Diameter of bolt = 3/4 in Number of bolts, n= 6 Size of plate = 1/2' * 9' It is asked to determine…

Q: Situation 2. Determine the value of the plastic load Wn Jusing the concept of collapse mechanism For…

A:

Q: Hand

A:

Q: write the stePs to Prove the follo wing Law.. %3D B. 2H JI ( कि- तिहो तार ।

A: Given data in question  Equation of Coutte flow To find out  Derive the relationship    Note Coutte…

Q: H.W: draw the I.L for RA, RC, RF, RD, MD, VCL, VG and MG.

A: Need to draw the ILD(influence line diagram)for

Q: What are the internal forces in the sections shown? 6 KN g ( g f c d 0.1 m 0.125 m -b <- CD- 6kN

A: Step 1: Step 2: Step 3: Step 4:

Q: W14 × 82 A992 steel 13'

A:

Q: Results and Discussion

A:

Q: RC Frame System Mostly used form of construction Columns and beams are not there Thickness of the…

A: RC Frame System 1.Mostly used form of construction to provide better strength and to increase the…

Q: LA WHAT IS THE MINZMUM THICK NESS FOR A SIMPLY 251 SUPPORTED SLAB /THE -> VZEW DIMEN SINS SHOWN VZEW…

A: Question (1)A As per ACI 318 code Table 9.5 minimum thickness defined for a slab simply supported…

Q: Prob.1: R. C. beam with dimensions b 250 mm, h 600 mm and d = 500 mm (fig. 1). If fe = 24 MPa, f=…

A:

Q: 1. Method of Joints: Find AB AC BD and BC (edited) 9 ft 9 ft A B -18 ft 18 ft- C 18 18 ft- D 6 kips…

A: Given: A simply supported symmetrically loaded truss with hinge support at A and roller support at…

Q: roblem No.1 Calculate the allowable uniform load W that the beam could carry. Assume fe' = 28M…

A: Given Characteristic Compressive strength of Concrete= 28 Mpa Design Strength of Reinforcement =…

Q: Q 3: Draw A. F. D., S. F. D., and B. M. 12 kN/m D. for the frame shown in Fig. (3) 100 kN B. 4 m…

A: We have to draw axial force, shear force and bending moment diagram

Q: Discuss about The unconfined compression

A: Unconfined compression: The strength of a material that can withstand the maximum axial compressive…

Q: B 3 ft 6 ft A 3 ft Draw SFD and BMD

A: Find the reactions consider ∑Fy=0VB+VA=12(3)(600)+600(6)+12(3)(600)as it is symmetrical beam…

Q: built up sections determine the centroidal moi of the built up section shown in the figure. it…

A:

Q: Attached pic is shear equation for calculation Tension equation for calculation is: Tdw= FyLwte/Ymw…

A:

Q: Design a solid timber roof beam to carry the loads shown (roof beam, no plaster). Assume the beam is…

A:

Q: Determine SFD and BMD Hinge Hinge 10 k 4 k/ft 4 k/ft 100 k-ft 6 k/ft 10 k 6' + 6 * s + s + s' +o *…

A: Since bending moment at the hinge is zero Take moment about C hinge from RIGHT side  -100 -…

Q: To the calculated area of cover plates of a build beam, an allowance for rivet holes to be added is…

A: given-cover plate of a build up beamrivet holes

Q: x' V3x - 5 dx

A:

Q: Why does the rigid connections in walls causes  penetration of sounds between rooms

A: Our homes should function as a quiet, peaceful environment for outdoor chaos. But that can be…

Q: 8 I The force on the 12mm thick link in the figure shown is 2960 N. If the pin has a diameter of…

A: Solution:   Given data Force applied = 2960 N thickness of plate t = 12 mm  Diameter of pin d = 10…