Power is transmitted between two shafts by a V-belt whose mass is 0.9 kg/m length. The maximum permissible tension in the belt is limited to 2.2 kN. The angle of lap is 170° and the groove angle 45°. If the coefficient of friction between the belt and pulleys is 0.17, find : 1. velocity of the belt for maximum power; and 2. power transmitted at this velocity. Note: Sketch the belt drive system for both parts and label the given data on it.

Power is transmitted between two shafts by a V-belt whose mass is 0.9 kg/m length. The maximum permissible tension in the belt is limited to 2.2 kN. The angle of lap is 170° and the groove angle 45°. If the coefficient of friction between the belt and pulleys is 0.17, find : 1. velocity of the belt for maximum power; and 2. power transmitted at this velocity. Note: Sketch the belt drive system for both parts and label the given data on it.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.70P: Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at...

See similar textbooks

Related questions

Q: Your team is prototyping a simple braking system for your model car. The 3.4 kg wheel with a radius…

Q: Don't use chatgpt will upvote

Q: Q1/A 6-in-wide polyamide F-1 flat belt is used to connect a 2-in-diameter pulley to drive a larger…

A: This question is related to the flat belts.The expression of angle of contact of the pulley.Here, C…

Q: The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of…

Q: 4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the…

Q: A selfpropelled truck of total mass 25 tonnes and wheel diameter 750 mm runs on a track for which…

Q: The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm…

A: Introduction In this problem, we will calculate the tension on each side of the belt and the power…

Q: A flat belt is required to transmit 35 kw from a pulley of 1.5 m effective diameter running at 300…

A: Given:P=35 KWd=1.5 mN=300 rpmθ=1124*2πμ=0.3t=10 mm

Q: HW9 In an engine governor of the Porter type, the upper and lower arms are 300 mm and 350 mm…

A: Introduction: A governor is a mechanism that is used to keep an engine's mean speed within set…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

Power is transmitted between two shafts by a V-belt whose mass is 0.9 kg/m
length. The maximum permissible tension in the belt is limited to 2.2 kN. The angle of
lap is 170° and the groove angle 45°. If the coefficient of friction between the belt
and pulleys is 0.17, find : 1. velocity of the belt for maximum power; and 2. power
transmitted at this velocity.
Note: Sketch the belt drive system for both parts and label the given data on it.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force exerted on the pressure plate is 75 lb. If Ri=4in., calculate the minimum acceptable value for RO. Assume that the clutch is new.
If PCD=6000lb and PGD=1000lb (both compression), find P and Q.
Find the power transmitted by a belt running over a pulley of 600 mm diameter at200 r.p.m. The coefficient of friction between the belt and the pulley is 0.25,angle of lap 160° and maximum tension in the belt is 2500 N.
Homework 2 A pulley is driven by a flat belt, the angle of lap being 120º. The belt is 100 mm wide by 6 mm thick and density1000 kg/m3. If the coefficient of friction is 0.3 and the maximum stress in the belt is not to exceed 2 MPa, find the greatest power which the belt can transmit and the corresponding speed of the belt.
Q3: An open belt drive with (200 and 150 mm) pulleys diameters, and the central distance equal to (0.5 m). The larger pulley speed is (500 r.p.m.), and the coefficient of friction between the belt and the pulley is (0.35). Calculate the power transmitted by the belt drive when the maximum tension on the belt equal to (2200 N).
. Find the width of the belt, necessary to transmit 7.5 kW to a pulley 300 mm diameter, if the pulley makes 1600 r.p.m and the coefficient of friction between the belt and the pulley is 0.22. Assume the angle of contact as 210° and the maximum tension in the belt is not to exceed 8 N/mm width.
5. Arough rule for leather belt is that effective tension in it, shall not exceed 15 N/mm of width for a belt of 10 mm thickness. This rule is applied to determine width of belt required to transmit 37 kW, under the following conditions : Angle of lap = 165°; Coefficient of friction = 0.3; Velocity of belt = 1500 m/min; Density of leather = 950 kg/m³. Find the width of belt required. Assuming limiting friction between belt and pulley rim, find the stress in the belt. [Ans. 140 mm ; 1.48 MPa]
Question 4 A pulley is driven by a flat belt, the angle of lap being 120°. The belt is 100 mm wide by 6 mm thick and density is 1000 kg/m. If the coefficient of friction is 0.3 and the maximum stress in the belt is not to exceed 1.5 MPa. Calculate: 4.1. 4.2. the speed of the belt in m/s using the information related to driving pulley. the centrifugal tension and the tension on the first tight side of the belt T1. the greatest power the belt can transmit. 4.3
A multi-disk clutch consists of two steel disks with one bronze disk. Theinner and outer diameters of the contacting surfaces are 200 and 250 mmrespectively. The coefficient of friction is 0.1 and the maximum pressurebetween the contacting surfaces is limited to 0.4 N/mm2. Assuming uniformwear theory, calculate the required force to engage the clutch and the powertransmitting capacity at 720 rpm
A double-ply leather belt transmits 10 hp from a motor with a pulley 8-in. in diameter, running at 1700 rom, to a 24-in. diameter pulley. The difference in tension may be taken as 20 lb/in. of belt width. Belt thickness is 0.2. Calculate the required width of belt
Two parallel shafts whose centre lines are 4 m apart, are connected by an open belt drive. The diameter of the larger pulley is 1.8 m and that of smaller pulley 3 m. The initial tension in the belt when stationary is 3 kN. The coefficient of friction between the belt and the pulley is 0.3. Calculate the power transmitted, when the smaller pulley rotates at 550 r.p.m. and length of the belt.
V-belt calculation