Power is to be transmitted from one shaft to the other by means if two rolling cones whose shafts intersect at 37 degrees. The shafts are to rotate in same directions with an angular velocity ratio of 2.5. The maximum diameter of the larger cone is to be 105 mm. Determine the cone angles and the maximum diameter of the smaller cone. FIGURE SOLUTION _degrees _degrees mm

Q: Determine the ratio of power

A: Given; Two shafts A and B are amde of the same material.Acc, to question;Diameter of shaft B is…

Q: Members that are joined together to form a kinematic chain Link Bar Pin Joint

A: As per company's guidelines we can answer only first question.

Q: or the Crank Double Slider Given, Choose a unique angle that is not the given(240). 181 - 59 degrees…

A:

Q: Using an engineer's level, the reading on a rod 60m away was observed to be 2.847m. The bubble was…

A:

Q: Due to slipping, points A and B on the rim of the disk have the velocities va = 7.2 ft/s and vg =…

A:

Q: EXERCISE 3.16 Collar A is welded to the vertical shaft, so is constant. The rectangular plate is…

A: Given: To find: Rotation transformation

Q: Determine the torque applied to the shaft of gear A when the acceleration of gear B is 25.5 rad/s^2…

A: Given, Angular acceleration of gear B = 25.5  rad/s2. Mass of gear A , ma = 20 kg Radius of…

Q: onnected by re of pin E ne periphery

A:

Q: The ring gear is fixed, and the hub and planet gears are bonded together. The connecting rod has a…

A:

Q: 2. How far from the axis of A will the center of the roller R be located if the angular speed of…

A:

Q: 3. Find the velocity of point C if the object below rotates about the line AB (A and B are fixed…

A:

Q: 4. Point A on the rod has a velocity of 84 to the right. Where is the IC for the rod? At what point?…

A: draw perpendicular to the both velocity vectors. IC is the point of intersection of those two lines.

Q: When does a curvillinear motion occurs?

A: Curvilinear motion This motion comes in play when an object starts to travel in the path with…

Q: quantity of oil into the well pipe, and he column of oil is then lifted to obtain a discharge into…

A:

Q: As shown in Fig. 10.17, consider the person performing extension movements of the lower leg about…

A:

Q: If the shaft is balanced by two counter masses located at 100 mm radii and revolving in Planes…

A:

Q: 2. A gear system is rotating without slipping. The outer ring is rotating clockwise at 30 rad/s. The…

A:

Q: ower is to be transmitted from one shaft to another which is parallel. The shafts are 12 in apart…

A:

Q: rad/s). What is the magnitude of the angular velocity (in rad/s) of the spinning top relative to the…

A:

Q: The crank of a slider crank mechanism rotates clockwise at a constant speed of 300 rpm. The crank is…

A:

Q: 9. How do you find an instantaneous center of zero velocity? 10. What is KENNEDY THEOREM? State the…

A:

Q: Problem 2 The are studying a planetary gear system. The outer gear ring is stationary. A motor that…

A:

Q: ower is to be transmitted from one shaft to another which is parallel. The shafts are 14 in apart…

A:

Q: the axes of which intersect but are inclined to each other at 22 degree are connected by means of a…

A:

Q: VC= UB 11 B Vmax= m/s m/s Ꮎ = 15 cm wheel pictured above is rolling while slipping. If the center of…

A:

Q: In the cam-follower mechanism shown, the cam has a total height of 5.25 cm and a base circle radius…

A: Given: Total height of the cam→h=5.25 Cm Base circle radius→r=1.75 Cm Length of the arm→a=10 Cm…

Q: Figure 7.7 shows a power hacksaw. At this instant, the electric motor rotates counterclockwise and…

A:

Q: 25 in., 25 in. 5 in. 5 in. Cord B' Two solid spheres (radius = 3 in., W=2 lb) are mounted on a…

A:

Q: Determine the x- and y-coordinates of the trapezoidal shape. 2.3 b b 1.7 b ४

A: Centroid is defined as the co-ordinates of the given plane figure where whole area of the surface…

Q: y b k.. a

A: Diameter of the part= a Diameter of the hole= c Distance between top edge of the part and top edge…

Q: A 5 hp motor running at 350 rpm drives an irrigation pump which has a pulley diameter same as the…

A: Given DataThe power of a motor is; FindFind the wrap angle

Q: P.1) A traditional set of cycling rollers has two identical, parallel cylinders in the rear of the…

A: Let's draw the schematic diagram of the set of whole cylinder rollers,  Determine the velocity of…

Q: A rigid bar is moving along two perpendicular walls. The length of the bar is LAB=1.0m. At an…

A: GIVEN DATA- A RIGID LINK MOTION GIVEN WE HAVE TO FIND I-CENTER OF LINK

Q: (a) The crankshaft AB shown in Figure 1.1 is rotating clockwise with an angular velocity of wAB = 6…

A:

Q: Given the system of gears below, the double gear is free to move along the horizontal.Determine the…

A: The free-body diagram of the system of gear is shown below.

Q: The bar shown in the figure is rotating in the counterclockwise direction with an angular velocity…

A:

Q: A shaft rotating with a uniform velocity of 11 rev/s for 5 seconds. It is then uniformly accelerated…

A:

Q: Part A Determine the angular velocity of link AB at the instant shown measured clockwise. Express…

A: Data given-  wCD = 7 rad/s

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.