Power in Amplitude Modulation at 100% Modulation An un modulated AM signal produces a current of 7.3 A. If the modulation is 100 percent, calculate i. the carrier powers ii. the total power iii. the sideband power when it is transmitted through an antenna having an impedance 60 Ω.

Q: A complex low-pass signal has a bandwidth of 500 kHz. What is the minimum sampling rate for this…

A: A complex low pass signal has a bandwidth of 500khz. What is the minimum sampling rate for this…

Q: B) Draw and find the BASK signal if maximum carrier amplitude is 14V and f.=0.1MHz and the input…

A:

Q: A telephone line uses speech signal of 4KHz and 8bit pattern to send 10kbps,the number of harmonics…

A: EXPLANATION Below is the answer for the given question. Hope you understand it well. If you have any…

Q: 1. Determine whether or not each of the following signals is periodic. In case a signal is periodic,…

A:

Q: Plot an example for ASK, FSK and PSK wave

A: Please upvote, I am providing you the correct answer below. Please please please.

Q: You need to double the strength of a signal but your transmitter cannot generate any more power. The…

A:

Q: (e) For a WiFi system, a hot spot has a bandwidth of 30 MHz. i. Calculate the channel maximum…

A: your question is about channel maximum capacity. let's see the solution of the question

Q: What can be done to fix signal attenuation problems?

A: Signal attenuation is whe­n a signal's strength or amplitude decre­ases as it travels through a…

Q: lex cable runs at T1 data rate cable is 2/3 the speed of light in the cable is

A:

Q: What affects does delay skew have on the signal?

A: Intro What effects does delay skew have on the signal?

Q: Problem 3 The modulating signal m(t) = 4 cos(200t) cos(400nt) is multiplied by the carrier c(t) =…

A: Since you have asked multiple question ,we will slove the first question for you .If you want any…

Q: QUESTION 12 -scale fading represents the changes in the signal over a short distance

A: Small scale fading represents the changes in the signal over a short distance

Q: Question 27 WRONG The period of a signal is 100 ms. Its frequency is

A: Introduction :Given,Period of a signal is = 100 ms we have to calculate its frequency .

Q: Assume that the 60-dB bandwidth of a receiver is 12 kHz and the 6-dB bandwidth is 7 kHz. What is the…

A: Given : 60 dB Bandwidth of a receiver = 12 kHz 6 dB Bandwidth of a receiver = 7 kHz We need to…

Q: Build Simulink model for QAM modulation and demodulation for sinusoidal waves of 100 and 200 Hz, and…

A: Answer:)

Q: Given the analog signal shown in figure, what are the 8-bit pulse code modulated values that will be…

A: Pulse Code Modulation (PCM): PCM is one of the encoding techniques used for converting analog data…

Q: Design channel code of 3 bit system to correct 1 bit error at the receiver

A: Here for a 3-bit system, we are indirectly told that we have 3 parity bits. And the task is to…

Q: Nyquist sampling rate is where fm is the maximum frequency of the analog signal sampled. a. greater…

A: Nyquist sampling rate is used in specifying the sampling rate

Q: Q6: Suppose the carrier waveform illustrate below with assuming a group of 10 information signals xi…

A: ANSWER:-

Q: Problem 2 In a DSB-SC system, the carrier frequency is 5 kHz and the message signal is given by m(t)…

A: Answer: I have given answered in the handwritten format in brief explanation

Q: If a signal has a frequency of 30KHZ what is the period in Microseconds?

A: given the frequency=30KHZ   The formula is,        f=1/s given     30=1/s   hence s=1/30= 0.33

Q: 2. You have a modem that can operate at a symbol rate of 9,600. Design a modulation system to allow…

A: Answer We need to use a modulation scheme that can transmit multiple bits per symbol i.e., 8PSK…

Q: A channel carries information at a signal-to-noise ratio of Ldb = 13 . Find the capacity of this…

A: Here We use Formula Shannon channel capacity C = B.log2(1+SNR) (in bits/second)  where B is the…

Q: The output signal from a conventional AM modulator is u(t)= 4 cos(3600pi t) + 24 cos(4000pi t) + 4…

A: The complete answer is given below.

Q: PPM modulation can be generated from PAM signal O False True

A: PPM modulation can be generated from PAM. Answer: False   In PPM, the amplitude and width of the…

Q: The transmission impairment that refers to a signal with high energy in a very short time is…

A: In this answer I will be discussing about the Impulse Noise.

Q: A sinusoidally modulated AM waveform is shown below: Determine: (a) Peak amplitude of the upper and…

A: According to our company's policy, we are obliged to answer only the first three questions in case…

Q: H.W. 1 Find the Nyquist rate and Nyquist interval for the following signals: 1. m(t)…

A: Answer 1

Q: The term that refers to loss of strength of a signal is called  attenuation explain?

A: The term that refers to loss of strength of a signal is called "attenuation."

Q: The effect of interference on FM system is high for large fi (fi<W) Select one: OTrue OFalse

A: The Correct Answer for the above question is "(a).True" Explanation: Here FM stands for Frequency…

Q: Determinethe bandwidthand baud for an tsR Signal with of 24K HZ. amark frequency of 32k H2, a Space…

A: As We know that :- 1.The Peak Frequency deviation is given by = |fm-fs|/2 for FSK signal 2.Where…

Q: Calculate the Nyquist rate for sampling when a continuous time signal is given by x(t) = 5 cos 100tt…

A: This can be solved as follows