Answered: Power Electronic. What is the constant…

Power Electronic. What is the constant A in the general solution of the current flowing through the thyristor? R = 5 ohm L = 10mH Alpha = 60 degree F = 50H

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Related questions

Q: Figure 12-70 + 10 V= (a) 100 V (b) 30 V + 1 μF 12.2 μF HH 100 pF 560 pF 390 pF 10 μF 4.7 μF HE 47 μF…

Q: The correct voltage waveform of the following clipper

A: Draw the The voltage waveform of the following clipper ?

Q: SHOW YOUR SOLUTIONS. In a common base connection, IC = 1 mA and IB = 50µA. Convert the values first…

Q: C1 =5 µF %3D C3 = 8 µF C2 = 4 µF C4 = 6 µF Cs = 4 µF DURACELL VT = 12 V Vhat is the voltage across…

Q: Determine the equivalent inductance seen at terminals a-b for the circuits A and B

A: The given circuits areWe need to find the equivalent inductance seen at the terminals a-b for the…

Q: What is the equivalent inductance between nodes a and b? 6 mH 3 mH 6 тH 6 тH ll O 2.6 mH O 5.0 mH О…

A: Option A is correct In parallel connection inductors will behave as resistance in parallel . In…

Q: 7. Determine all of the resistor values in figure below. if RT = 7730. 15.53 mA R₁ 3.64 mA R₂ ww +1₁…

A: Given Circuit:Total resistance, To determine:Value of resistances

Q: A LED which bright one color when forward and another color on reverse is called One directional LED…

Q: C1 L1 4.3µ 7.7m =>f = 23 kHz V1 C2 R1 6.8k 5.9µ AC 0.84 0 R2 140

A: KCL states that algebraic sum of current at a node must be equal to zero. It is also called nodal…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

100%

Power Electronic.

What is the constant A in the general solution of the current flowing through the thyristor?

R = 5 ohm

L = 10mH

Alpha = 60 degree

F = 50Hz

Alpha
Alpha +180°
LOAD
T2
V
network
(wt)= 220*V2* sin(wt)
LOAD
+

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What do you calla closed conducting path? A Node B Short circuit C) Loop Junction
maq Q1
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
Ip Ep=40 V f = 60 Hz N₂= 20- N₁ = 120 Find the maximum flux om om = Find the magnitude of the induced secondary voltage Es Es = units + Is Es units If the coefficient of coupling (k)= 0.75, determine the magnitude of the induced secondary voltage Es Esk=0.75 = units
If the core of LVDT is at the middle, then the output voltage will be a. maximum b. minimum c. Output voltage is no relation with core position d. 0
A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of the Thyristor (5 µA) and frequency (50 Hz). Find the rate of voltage changing with time and snubber circuit power losses?
What will be the value of the twiddle factor: W42
5.) Find the percent overshoot, settling time and peak time for 0.04 T(s) == 240.002s +0.04
Q1- The given ferromagnetic core relative permeability is 800. Determine the total reluctance of the core. 35 cm 10 cm 20 cm 5 cm 15 cm 45 cm 15 cm 15 cm 10 cm
Question 1 A ferromagnetic core with a relative permeability of 1500 is shown in Figure 2. The dimensions are as shown in the diagram, and the depth of the core is 7 cm. The air gaps on the left and right sides of the core are 0.070 and 0.020 cm, respectively. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 400 turns in the coil wrapped around the center leg of the core and if the current in the coil is 1.0 A, what is a) the flux in each of the left, center, and right legs of the core? b) the flux density in each air gap? 7 cm ст ст 30 cm 30 cm 7 cm 400 turns 0.05 cm 30 cm 0.07 cm 7 cm Core depth = 7 cm Figure 2
Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a) Exciting current (ii) Ic (b) Magnetizing Current (iii) Ie (c) core loss current