1_4Potentiometer:The resistive wire AB in the circuit shown has the length of 80cm.When switch S is open, the Galvanometer reads zero for L = L1 =0.4m. when switch S is closed, the Galvanometer reads zero forL = L2 = 0.2m. Therefore, the internal resistance (7) of the battery is:4VABE1*.1RR r12 ΩSelect one:O a. 12 2b. 62O c. 42O d. 3 2

Answered: Image /qna-images/answer/358a161d-54d0-4fbb-9291-1551e1702fb4.jpg

Potentiometer: The resistive wire AB in the circuit shown has the length of 80cm. When switch S is open, the Galvanometer reads zero for L = L, = 0.4m. when switch S is closed, the Galvanometer reads zero for L = L2 = 0.2m. Therefore, the internal resistance (7) of the battery is: 4V A B E 1 4 1 L, r 1 *. R 12 Ω Select one:

Potentiometer: The resistive wire AB in the circuit shown has the length of 80cm. When switch S is open, the Galvanometer reads zero for L = L, = 0.4m. when switch S is closed, the Galvanometer reads zero for L = L2 = 0.2m. Therefore, the internal resistance (7) of the battery is: 4V A B E 1 4 1 L, r 1 *. R 12 Ω Select one:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a fully charged voltage per cell of about 6.1 V, and capacity of 7.053 Ah each. Themodule has 71 cells in series and 34 cells in parallel. Calculate the voltage and energy.
show solution please
D.C voltmeter
Find the unknown quantities for the circuits below using the information provided. E= I R₁ P=8W R₁ = 16 N www R₂ P=4W 1Ω
Continuing with the same setup as above, where you connect a 6Q resistor and a 12 Q resistor in series to a 9 V battery. Find the potential difference, V1, across the 6 Q resistor in Volits Hint: VTOT = V1 = V2. RTot ITot BAT1 R2 12 Q R1 9 V
Explain this diagram
Simplify the circuit of Figure 2 and find the current flowing out from the voltage source. 22 Q 20 Q + 250 V 750 140 Q 60 Q 10 Q 12 Q Figure 2
Find the unknown quantities for the circuits below using the information provided. E= I R₁ P=8W Rr = 16 N www R₂ P=4W 1Ω
1. Design the voltage divider of Figure 1 such that Vri = 4VR2. 20 V R2 Figure 1
Suppose that the components of the circuit shown in figure below, have the following values:R1= 16Ω , R2= 18Ω , R3=30Ω , R4=9Ω , R5= 4Ω .The voltage across AB is measured by a voltmeter whose internal resistance is 250Ω .What is the measurement error caused by the resistance of the measuring instrument?
Needs Complete solution.
Two resistors R1 (100KΩ) and R2 (50 KΩ) are connected in series with a 150 Volt voltage source, if you want to measure the voltage at R2 with voltmeter 1 (sensitivity = 1KΩ/V) and voltmeter 2 (sensitivity = 20KΩ/V). Determine (a) the readings per voltmeter, (b) the percentage error of each reading. (make a picture of the circuit first).