Post, IB, IE, VC,VCE and VCE.

Q: In which method of fault diagnosis ,the input test signal is applied to each stages individually ? O…

A: The correct answer is dynamic testing.

Q: The Companding occurs only when; O a. Small and large signals are attenuated O b. Small and large…

A: Note : The correct option D. Small signal amplifier and large signal attenuated. With companded PCM…

Q: What oscillator structure is the circuit in the picture? Calculate the oscillation frequency of the…

A: According to question: a) The given oscillator structure is Colpitts oscillator and are generally…

Q: What is the advantage of using J-FET? a. Fail-safe O b. High predictability Oc. All of the above O…

A:

Q: For an op-amp integrator with R = 100KOhms, C = 10UF and a square wave input signal, the output…

A:

Q: What is the name of the signal which is indicated by the red line? 4- O A) Feedback B) Disturbance…

A: The given feedback system is non unity negative feedback system.   Here they have mentioned the…

Q: At what voltage will the upper comparator produce a low output of the 555 timer IC? Capacitor is…

A: When the capacitor is charging to a voltage lower slightly than 2/3Vcc, the output of the upper…

Q: In measurement system, are needed where the output variable of a primary transducer is in an…

A: Energy from one form to another will be converted using a device called transducer. It is mainly…

Q: III) Compare analog and digital CRO.

A: The main difference between analogue oscilloscope & digital oscilloscope is that such an…

Q: C/ Calculate load regulation of 7805 regulator has full load output voltage of 5.15 * V and no-load…

A:

Q: Define on-off ratio. Why series JFET has higher on-off ratio as compared to shunt JFET?

A: The series JFET is largely used as compared to the shunt JFET because of the high On-OFF ratio.

Q: Counter Output Question. input. 60 Hz rrr MOD-6 Counter Decade Counter Output (Hz)

A:

Q: G/ Desigh a square wave osillatr for Bequensy ZHZ and Sketch the Corresponding circait and the ut…

A:

Q: What is FR4?

A: Answer: to find about FR-4

Q: 3Z The most usual form of op-amp package a.type TO-5 metal cans b.integration packages c.dual…

A: Examples of OP amps used in Electronics circuit design INA180 INA181 TSV911ILT TS911RILT…

Q: 70) Which of the following application or operation of Timer IC operations produces an output that…

A: Multi vibrator: Multivibrator is an electronic device. This device is used to implement the two…

Q: Flash/Parallel ADC use the following key components: Input Resistance + Amplifier Amplifier +…

A:

Q: How does R-2R DAC is better than Binary-weighted Resistor DAC?

A: Given that  How does R-2R DAC is better than Binary-weighted Resistor DAC?

Q: 1 use direct subfarction on the following binary numbers: ☺ lloo- lool

A:

Q: Both stages in a 2-stage amplifier have a dominant lower critical frequency of 500 Hz and a dominant…

A: lower critical frequency 500 HZfL= 500 Hzupper critical frequency fH=80KHz    =80 * 103 HzTo find…

Q: Q) is the minimum level of instrument input. O Tolerance. O Threshold. O Resolution. O Range.

A: The measurement devices are used to measure electrical quantities. The true value and the measured…

Q: What is the baud rate? What are some typical baud rate values for instruments.

A: In this question we have to write the baud rate definition and write some typical baud rate values…

Q: Which of the following provides the process transconductance parameter? O a. H„Cox O b. none of the…

A: The solution is given below

Q: second modulating tone having the same amplitude but a different frequency is added to the first at…

A: We need to find out modulation index

Q: Find the delay generated by Timer0 if the following values are used with 10MHz oscillator TCNTO Ox…

A: Given f=10 Mhz TCNT0 =5E

Q: The purpose of analog low pass filer at the input of DSP system is to band limit the input signal.

A: A low-pass filters a filter that passes signals with a frequency lower than a selected cutoff…

Q: Q5/B- What the difference between encoder and priority encoder

A:

Q: Digital signal where frequency of massage 4000 and Quntzation value 4?? ۱:۰۲ ↓↓

A:

Q: Am 11 KV /33 KV 220 MVA, 60 Hz transformer is wooded at sy. with resistive to ad Ratio 21 KW at…

A: In this question we need to find a copper loss at 50% and 75% loading

Q: Temperature compensation of Strain Gauges

A:

Q: Kindly assist to check if the new design I made with the insertion of this multiplexer works.

A: According to the question, we need to check the design shown below

Q: What is the difference between the connectors RJ11 and RJ45?

A: "RJ" stands for registered jack and 45 is the interface standard To have a ethernet connection to a…

Q: Vertical Amplifier is used in CRO to Select one: a. Amplify signal from input b. Delay the input…

A: Input signal is given to vertical amplifier

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.