please. answer the second part The ratio arms of the Kelvin bridge (shown) are R1=R2=b=a=350 0. The galvanometer has an internal resistance of 550 Q and a current sensitivity of 180 mm/ µA. The unknown resistance Rx = 0.1005 Q and the standard resistance is set a 0.1000 Q. A dc current of 2 A is passed through the standard resistance from a 2.2 V battery in series with a rheostat. The resistance of the yoke may be neglected (Ry-0 which is a good approximation for this problem). Answer the following questions: Rs A) the deflection of the galvanometer mm The resistance unbalance required to produce galvanometer deflection of 1 mm

please. answer the second part The ratio arms of the Kelvin bridge (shown) are R1=R2=b=a=350 0. The galvanometer has an internal resistance of 550 Q and a current sensitivity of 180 mm/ µA. The unknown resistance Rx = 0.1005 Q and the standard resistance is set a 0.1000 Q. A dc current of 2 A is passed through the standard resistance from a 2.2 V battery in series with a rheostat. The resistance of the yoke may be neglected (Ry-0 which is a good approximation for this problem). Answer the following questions: Rs A) the deflection of the galvanometer mm The resistance unbalance required to produce galvanometer deflection of 1 mm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The diode starts to conduct when the voltage across it is 0.6 V. Vin is a variable DC voltage source. R1 = 12.2 Ω and R2 = 6.7 Ω. At what value of Vin in volts will the diode start to conduct if Vin is increased from zero.
4. With reference to the Paschen curve below, Breakdown voltage (V) 60 55 50 45 40 35 30 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 pd (cm-torr) If a discharge at p = 0.1 torr, d = 20 cm is to be initiated, what is the voltage required to cause a breakdown? What will be the breakdown voltage if p = 0.025 torr, d= 20 cm?
According to the figures, the required load for the zener diode to regulate in the circuit is minimum how many ohms is its resistance?
For the Precision Rectifier in Figure 3, what is the output voltage equation during the Negative-Half Cycle using ideal diodes? choose the correct answer: 1)V0=0V 2)V0=-Vin 3)V subscript o equals negative R subscript 1 over R subscript 2 V subscript i n end subscript 4)V subscript o equals fraction numerator negative R subscript 2 over denominator R subscript 1 end fraction V subscript i n end subscript
(2) Labäi If a FET has a pinch off voltage = . 4 -1V , ID=1mA, and Vgs=0V, What is ?the value of IDSS b) 1mA O c) 0A O d) 100mA O a) 1A O
1. How is the capacitor value here calculated? 2. Make a circuit analysis
O has more bandwiath The circuit has two oppositely connected ideal diodes in parallel. What is the current flowing in the circuit? 20 www D2 D1 30 ww 40 12V O 1.33 A O 2.0 A O 1.714 A O 2.31 A
Determine the voltage across the resistor R2. (assume Zener voltage is 3 volts and Diode forward voltage is 0.7V)
Please solve asap.
For the diode circuit of the figure below: 1. Determine v, and sketch its waveform for at least 4 cycles 2. Determine the average (dc) voltage established the load Show the details of your work. Without a complete solution (step-by-step solution) will invalidate your answer. 120 V 2.7 kN -120 V
Find R. (See figure 1 and 2)
The single-phase bridge rectifier of Figure below is required to supply an average voltage io of Vdc = 300 V to a resistive load of R = 15 2. Determine the voltage and current ratings of diodes and transformer. D₁ D₂ D3 D₂ www vo