Please consider an adiabatic turbine operating in an environment with T= 300 K. The turbine accepts an Ideal Gas at 550 K and 4 bar at the rate of I molelsec and discharges the gas a 415 K and 1.5 bar. Cp of the Ideal Gas = 20.785 J/ K-mole. %3D Please find: Ws, Wideal, and W1ost in kW; $, in W/°K,and n..

Q: In a gas-turbine plant working on a Brayton Cycle, the air at the inlet of the compressor is at 25C…

A: Ideal gas Brayton cycle for gas-turbine plant contains 4 processes: A-B adiabatic reversible…

Q: A liquid has a molar volume of 0.2 L/mol at 400 K and 4 bar. This liquid is compressed with a pump…

A: A. Work done by the pumpThe work done by the pump is given by the following formula:wheren is the…

Q: Q1) A steam with a quality of 69%, enters an adiabatic nozzle at 3.5 MPa and leaves at 0.4 MPa and…

A:

Q: exit velocity and what is the cross-sectional area at the nozzle exit f

A:

Q: air is entering a compressor at 373.15K and 500kPa, it exits the compressor at 520K and 1200Kpa.…

A: Given :Air entering temperature of the compressor  Air entering pressure of the compressor Air exit…

Q: PO A feed stream containing 50 mol/s of a wet steam (95 % Vapor, 5% liquid) at 2 bar is compressed…

A: Wet steam means steam which consist of water vapor and drops of liquid water. Compressor is a…

Q: Determine the power requirement (in kW) of the compressor if 5 mol/s of the gas flows through it

A: given data  T=300K P1= 1 bar P2=20 bar T2= 700K

Q: In a petrochemical industry, ethane is stored in a 3300 L vessel at a pressure, 22 bar and…

A:

Q: Air compressor Steam turbine

A: Answer. Data given below:-

Q: a) Draw a P-V diagram for the above processes. Clearly label the axes with relevant values and draw…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: = heat transfer rate from the compressor in kW

A:

Q: ca gas Wi 2. Steam at 2500 kPa and 350° C enters a turbine and leaves at 10 kPa. The turbine…

A:

Q: Please solve all the choices

A: Question 1For an ideal gas:The relation for an ideal gas between specific heats at constant pressure…

Q: The tank below in figure 1 has oil and water. An open ended U-tube manometer is attached near the…

A:

Q: Problem 3: The following data are from a system that undergoes a thermodynamic cycle between three…

A:

Q: Steam enters an adiabatic turbine at 2MPA, 400°C at a velocity of 50 m/s. It leaves at 15 kPa and…

A:

Q: 1. Please consider steam at 500 kPa and 300 C. Please determine a. a and g in k.J/kg. b. R in cc/gm.

A: Steam at 500 KPa comes in superheated region. Steam pressure, P=500 KPa Steam temperature, T=300°C

Q: For  each of the cases below, determine if the heat engine satisfies the first law and if it…

A: First law of thermodynamics: First law of thermodynamics represents the law of conservation of…

Q: c) A Carnot refrigerator provides 10 kW of cooling at -20 C and discards heat at 30 °C. Calculate…

A: Answer:c) Given:  Low temperature = TL = -20 c  = (-20 + 273) K = 253 K  High temperature = TH = 30c…

Q: A 2.5 mol sample of an ideal gas with a molar specific heat Cv=5/2R always starts at pressure…

A: Here we have to determine the change in internal energy, heat added and workdone for a sample of gas…

Q: a flash chamber via a valve. Saturated vapor and saturated liquid steams, each at 4 bar, exit the…

A: Pressure entering at the flash chamber P1 =15 bar Temperature T1=1800C Mass flow rate m1=5 kg/s…

Q: Air enters a compressor operating at steady state at 1.05 bar, 300 K, with a volumetric flow rate of…

A:

Q: For the given question and solution, for part (b), finding the work input  of the saturated vapour…

A: A compressor is used to compress steam at two different phase of steam.

Q: Acetylene behaves ideally as it goes through an isentropic process from 6 bar to 2 bar The initial…

A: The reversible adiabatic process is an isentropic process. The pressure and volume product with heat…

Q: Q2: A 1.2-m tank contains 6.5 kg of steam at 0.6 MPa. Determine the temperature of the steam, using…

A: Volume of the tank, V = 1.2 m3 Mass of the steam, m = 6.5 kg = 6500 g Pressure of steam in the tank,…

Q: Ideal Gas — A piston contains 250 moles of an ideal monatomic gas that initially has a pressure of…

A: Work done, heat and internal energy for each process is to be calculated.

Q: An engineer needs saturated steam at 100C with a flowrate of 550 kg/h from an ice block using the…

A:

Q: Q1:Air enters a diffuser at 200 m/s with a pressure of 80 kPa and a temperature of -20°C. It leaves…

A: Note: We are authorized to answer three subparts at a time, since you have not mentioned which you…

Q: 4. In a steady-flow process carried out at 3 bar, 1 mole - of air at 450 K is continuously mixed…

A: As it is not mentioned which question to solve, we are solving the first one series. The rate of…

Q: (a) Air in a piston-cylinder device undergoes a process that follows the relation shown in Figure 1…

A: Given :Initial pressure,                               Initial Temperature, Final pressure, Final…

Q: 2. A system has heat capacity at constant volume C, = 0.042 T. The system is initially at 20OK and a…

A: A system have Heat capacity Cv=0.042T2 J/K System temperature T1=200K Thermal reservior…

Q: Q3: Assume ideal gas behavior, and compute the reversible work required to compress a natural gas…

A:

Q: piston-cylinder assembly contains 2 lb of water initially at 100 lbf/in² and 400°F. The water under…

A:

Q: A 1200 L vessel contains 85 gmol of nitrogen. The vessel can withstand 25 kPa above atmospheric…

A: Given, Volume of Vessel V = 1200 L = 1200 × 10-3  m3 Mass of Nitrogen m = 85 gmol Maximum Pressure…

Q: a. H and S for superheated steam at 80 kPa and 520 °C b. Tand V for superheated steam at 100 kPa…

A: If steam temperature is more than its vaporization point then steam is superheated steam .…