Please answer nos. 7, 8 and 9N=82M=132L=102 (7) Determine the net area of thepath 1-2-3-4 if b = 30 mm -(mm²)(8) Determine the net area of thepath 1-2-4 if b = 30 mm –(mm?)(9) Determine the net area of thepath 1-2-3 if b = 30 m - (mm?)(10) Determine the net area of thepath 2-3 if b = 30 mm - (mm²)(11) Determine the net area of thepath 2-4 if b = 30 mm - (mm²)(12) Compute the tensilestrength of (17) Which of the followingThe figure shows a plate having a width of 400 mm and thickness ofconnected to another plate by 34 mm o bolts as shown in the figure 2.22. Assumediameter of holes to be 2 mm larger than the diameter of the bolts. Use A 36 steelplate with yield strength F, = 248 MPa and minimum tensile strength F, = 400 MPa.mm is to be(14) Compute the allowablestrength of the connectiondue to fracture in the netsection. (ASD Method) – (kN)(15)For a chain of holes extending across a part in any diagonal or zigzag line, the netwidth of the part shall be obtained by deducting from the gross width the sum of thediameters or slot dimensions of all holes in the chain and adding, for each gage spaceCompute the design strength ofthe connection due to yielding ofthe gross section. (LRFDMethod) – (kN)(16)in the chain, the quantity , where S is the longitudinal center to center (pitch) ofCompute the designstrength of the connection dueto fracture in the net section.any consecutive holes, in millimeters and g is the transverse center to center spacing(gage) between fastener gage lines in millimeters. If aL mm.mm,c = M mm andd =(LRFD Method) – (kN)the connection due to shear offailure of bolts. Fy = 270 MPagives the nearest value of "b" sothat the net width along bolts 1-2-3-4 is equal to the net widthalong bolts 1-2-4?- (mm²)- (kN)(13)N = 80 + BM = 100 + YComputethe allowable strengthof the connection due to yieldingof the gross section. (ASDMethod) – (kN)L= 100 + BlabPNE ---

Given data N=82, M=132 and L=102 Need to find Question number -7, 8 and 9

Answered: Please answer nos. 7, 8 and 9 N=82…

Engineering

Civil Engineering

Please answer nos. 7, 8 and 9 N=82 M=132 L=102

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

اجب عن السؤالین ادناه وارسل الاجابة على شكل صورة او ملف PDF * Q 1: For the triangle below, Find the length of (d) by using Sine Law? Q 2: For the triangle below, Find the length of (x) by using Cosine Law? 60° d/ 80° 7m إضافة ملف هذا السؤال مطلوب
B9
Q2 calculate the Vertical movement of point A 4 m t Steel wire D = 25 m E = 20X10 +4 + 4.1 2 4 20KN Steel wis D = 60 E 20x10 2m + 3 kľu 60 A 60 kuu
Consider W=1290KN/m
13. Determine the numerical value of the factor (A/F, 5%, 10). A 0.0795 B 12.5779 0.1295 D 7.7217
Questions T 40 mm TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C₁ C₂ 1.0 0.208 0.1406 1.2 0.219 0.1661 60 mm 1.5 0.231 0.1958 2.0 0.246 0.229 2.5 0.258 0.249 3.0 0.267 0.263 4.0 0.282 0.281 5.0 0.291 0.291 N 10.0 0.312 0.312 0.333 0.333 1. Determine the largest torque T which may be applied to end of the solid bar which is shown in the diagram above, knowing that the maximum allowable shear stress = 107 MPa and G = 40 GPa. Provide the answer in kNm with precision to two decimal points. 2. The same solid bar is subjected to a torque of 1.5 kNm. Its total length, denoted as z, is 601 mm. What will be the angle of twist? Provide the answer in degrees with precision to two decimal points.
1. Determine Ix and ly of the shaded area. Use 3 decimal places for the final answer. r2 A Given I A = 15 in B = 6 in C = 4 in r1 = 3 in r2 = 6 in B.
5.0 m (100+SN) KN> 144 KN 5.50 m E 6.0 m C 7.0m K 5.0 m O 120 KN 96 KN M U W Note: SN is the sum of your Student Number, e.g. 201802475=2+0+1+8+0+2+4+7+5 = 29 Instruction: Solve the following problem completely using portal method and write the solutions neatly in the plate template. Summarize your final answers at the end of each problem. Round off your answers to 3 decimal places. 1. Portal Method: The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X are rigid supports. Determine the following: a) The shear forces in columns and girders. b) The axial forces in columns and girders. c) The moment at the end of each member. d) Summarize your results by drawing the frame with the internal forces. 4.0 m R 4.20 m 4.50 m 5.0 m
ASAP please help now. Be careful on the gven. Round off to 3 decimal places. I will give thumbs up. Thank you!
Use the VIRTUAL WORK method to answer the following question(s). Show clear and full solution. In the structure shown, find the horizontal movement of H knowing that the horizontal members of the structure are 2-L-35 x 35 x 3 mm angle bars, vertical members are 2-L-50 x 30 x 3 mm angle bars and diagonal members are 2-L-35 x 35 x 3 mm angle bars.
X = 929 Y = 45 A = 1
deflection @ point C, Yc using area method or double integration method