Pick the right combination of True Statements. 1. As the by-pass factor (BPF) of the cooling coil increases, temperature difference between air at the outlet of the coil and coil ADP decreases. 2. As the by-pass factor (BPF) of the cooling coil increases, temperature difference between air at the outlet of the coil and coil ADP increases. 3. During cooling and humidification process, the enthalpy of air may increase, decrease or remain constant depending upon the temperature of the wet surface. 4. During sensible cooling of air, dry bulb temperature decreases but wet bulb temperature remains constant 5. The sensible heat factor for a sensible heating process is 1.0

Pick the right combination of True Statements. 1. As the by-pass factor (BPF) of the cooling coil increases, temperature difference between air at the outlet of the coil and coil ADP decreases. 2. As the by-pass factor (BPF) of the cooling coil increases, temperature difference between air at the outlet of the coil and coil ADP increases. 3. During cooling and humidification process, the enthalpy of air may increase, decrease or remain constant depending upon the temperature of the wet surface. 4. During sensible cooling of air, dry bulb temperature decreases but wet bulb temperature remains constant 5. The sensible heat factor for a sensible heating process is 1.0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The data table below shoes the dry-bulb and wet bulb temperatures measured with a psychrometer on four different days at the same location. According to the data shown in the table, which day had the highest relative humidity? Temperatures Measured with a Psychrometer Day 1 2 3 Dry-bulb temperature (°C) 0 5 10 Wet-bulb temperature (°C) -5 0 5 2 3 4 O 1 4 15 10
The following data were obtained from space cooling load survey of an Air-Conditioning (AC) system of a Conference Hall: Sensible Heat Load Latent heat Load 10.5 tons 2.0 tons Design inside condition is set at 22 C dry bulb temperature and 60 percent relative humidity. Cold air is supplied to the Hall at 14 °C. The AC system is designed with mass ratio of 4:1 total supplied cooled air to required minimum outdoor ventilation air. Outdoor air is 30 °C dry bulb and 70 % relative humidity. Determine: a) Recommend an AC system suitable to the set-up above. b) What is the air-cooling apparatus SHF? c) What is the probable Apparatus Dewpoint (ADP)? d) What is the probable cooling coil Bypass Factor (BPF) of the cooling apparatus? e) Fan capacity needed that supplies air to the hall in liters/hour f) Refrigeration capacity of the Air-Cooling Apparatus in tons FOCL
2. Air flowing at 2 kg / s has a dry ball temperature of 60 ° C and a wet bulb temperature of 30 ° C, mixed with another air stream flowing at 3 kg / s at 25 ° C and a relative humidity of 50%. Using a psychrometric chart determine the air flow properties of the mixture. (a) humidity ratio = (kg water / kg air). b. Enthalpy = (kJ / kg) c. Dry bulb temperature. = (° C)
The total volume of a new house is 681 m3. Before the heat is turned on, the air temperature inside is 15°C, and the relative humidity is 42 percent. After the air is warmed to 20°C, how much water vapor must be added to the air to make the relative humidity 42 percent? _________kg
Which one of the statements is correct? The Kelvin-Planck and Clausius statements of thermodynamics are equivalent. In order to proof the equivalence, the process is to demonstrate that _______ A. the violation of the Clausius statement leads to the violation of the Kelvin-Planck statement B. the compliance of the Kelvin-Planck statement leads to the compliance of the Clausius statement C. the compliance of the Clausius statement leads to the compliance of the Kelvin-Planck statement D. the violation of the Kelvin-Planck statement leads to the violation of the Clausius statement
in a cooling process, the _____ and _______ of the air-water mixture do not change.
An air-conditioning system to be installed in a factory with sensible and latent cooling loads of 175 KW and 65 KW, respectively. Assume that the relative humidity of supply air is 90%. The inside state is at 21 °C DB and 70% RH. What is the approximate required dry-bulb temperature in °C of the supply state of air? Select one: O a. 17 b. 16 O c. 18 O d. 14.5 Oe. 14 L
During performances, a theatre experiences a sensible heat load of 500,000 Btu/hr and moisture load of 175 Ib/hr. Air enters the theatre at 65°F and 55% relative humidity and is removed when it reaches 75°F or 60% relative humidity, whichever comes first. What is the ventilation rate in mass of air per hour?
An apartment has the dimensions 12 m by 6 m by 4 m. The temperature is 30°C, and the relative humidity is 56 percent. What is the total mass (in kg) of water vapor in the air in the apartment? _______ kg
In the case of heating the air with a heating coil, the absolute humidity of the air can either increase, or decrease. does not change. increases. decreases.
Required information Problem 14.108 - Cooling Tower Assessment NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The cooling water from the condenser of a power plant enters a wet cooling tower at 40°C at a rate of 91 kg/s. The water is cooled to 25°C in the cooling tower by air that enters the tower at 1 atm, 23°C, and 60 percent relative humidity and leaves saturated at 32°C. Neglect the power input to the fan. Use data from the psychrometric chart and tables. Problem 14.108.a - Cooling Tower Assessment Determine the volume flow rate of air into the cooling tower. m³/s. The volume flow rate of air is
6. A working area of a mine has diesel equipment operating within it. The maximum diesel loading is 750 kW. The same section of the mine also has a methane inflow of 0.25 m³/s flowing into it. If the maximum permissible methane concentration in the general body of the air is 0.5% and the design diesel air quantity is 5 m³/s per 100 kW of installed diesel power, determine the required ventilation flow rate for the working area.