peton with a relative density of 0.78 flows upward in a vertical venturimeter having a discharge coefficient Cd of 0.98.it has a diameter of 160mm and 80mm at inlet and throat respectively.U Tube manometer connected by normal way and shows level of different  of 299mm   determine ,1) the flow rate??

Q: what is flow rate of the sy stem below and what is the power t input of the pump if it is and the…

A:

Q: Points A and B are 4800 m. apart along 60 cm. pipe diameter carrying water. B is 10 m. higher that…

A:

Q: At a point in a 15 cm diameter pipe, 2.5m above its discharge end, the pressure is 250 kPa, If the…

A:

Q: stants, calculate the time required for the discharge through the orit D. The initial level…

A:

Q: 1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm…

A: Given data  Flow rate = 500 gpm Pressure = 35 psi Density = 62 lbm/ft^3 Find the pump head

Q: Find gage pressures (2) and (3).

A: This question is based on the concept of gauge pressure.

Q: The velocity measurement observation manometer readings are 43 cm , 46.5 cm. The pipe diameter is…

A:

Q: Ex:- 200 L/see water flow in Verrtical PiPe, The tiameter for The small pipe (75 mm) expandeA by…

A:

Q: Fox flow rate 28 Lis Find. EL. 60M puup Power 100 mm.

A: Givenflow rate Q=28ltr/s=0.028m3/sat point 1diameter of pipe at inlet d1=150mmelevation Z1=30mAt…

Q: en:L-foom, D= 50mm, L2= 100m, D= 10omm %3D A (Arall pipor).0.032, Find:. a- Dscharge oteach Pipe b.…

A: The equivalent diameter of the pipe can be easily calculated using the formula given below as-…

Q: dl Calculate the volumetric flow rate of water through a pipe with an inside diameter of 0.18 m…

A: d1=0.18m , d2=0.11m x=0.3m , Cd=0.67

Q: The velocity measurement observation manometer readings are 44.5 cm , 47.5 cm. The pipe diameter is…

A: Solution:

Q: What kinds of Differential Pressure Flow meters? And discuss them.

A: Flow meters which are based on the differential pressure measure the velocity of fluid by reading…

Q: The velocity measurement observation manometer readings are 44.5 cm , 48.5 cm. The pipe diameter is…

A: Given data:

Q: Given a frictionless flow of water at 125.6 ft^s in a long, horizontal, conical pipe, of diameter 2…

A:

Q: Q. No 3). A water supply pipe line is designed to supplying water to a nearby city. Determine…

A:

Q: bat diameter ovifice hoie , dis needed nditions the flow rate through the orifice meter is to if…

A: Solution is attached below:

Q: Determine the discharge for laminar flow

A: Given: pipe diameter d=0.04 m centre line velocity  =1.5 m /s I;e  centre line velocity or maximum…

Q: 010. Water is pumped from the large tank shown in Fig. The head loss is known to be equal to 4v/2g…

A: The head loss, hL=4*V22gPump head, hp=20-4Q2Pipe area, A=0.10 ft2Elevation difference, ∆Z=Z1-Z2=13…

Q: 9. How is the cleanliness of a hydraulic

A: Concept: 1) It is generally measured based on number of solid particles in it.  2) If there are more…

Q: coefficient of discharge=

A: Given: h1=314 mm h2= 286 mm Q=165 ltter/s A1=338.6 mm2 A2=84.6 mm2 To determine: The coefficient of…

Q: A two branch duct system of circular duct is shown below. The fittings have the following equivalent…

A:

Q: A pipe experienced a total head loss of 15 m, determine the pressure difference from its starting…

A:

Q: The flow rate of water of mass density of 998 kg/m^3 and viscosity of 1.002 x 10^-3 kg/m-s, through…

A:

Q: For transferring of water, a pump is installed in the height of 3 m above the surface of the water.…

A: hsp=Pρg=100kpa1000×9.81=10.19hs=3mhf=4mhvp=Pvρg=10kpa1000×9.81=1.019

Q: The flow rate of water of mass density of 998 kg/m^3 and viscosity of 1.002 x 10^-3 kg/m-s, through…

A:

Q: Explain and Plot why the Head(H) arrive in meter(m) unit

A:

Q: The velocity measurement observation manometer readings are 44.5 cm , 49 cm . The pipe diameter is…

A: Solution:

Q: An orifice meter with orifice area 804 mm2 is inserted in a pipe of area 1608 mm2 .The pressure…

A:

Q: A two branch duct system of circular duct is shown below. The fittings have the following equivalent…

A:

Q: Q.3 b) A total of 14 litres per second of oil is pumped through two pipes in parallel, one 12 cm in…

A:

Q: a) The pressure head supplied by the pump, b) The total head loss between point b and 2.

A:

Q: a CS BPA 1 6.7 A pipe of diameter 400 mm carries water at a velocity of 25 points A and B are given…

A: This question is solved by the law of conservation of energy  It states that energy can neither be…

Q: Question 7 find the wter pressure at pipe in this system? (Use HAZEN- WILLIAM CH-130, 0-1.2 m³/s…

A: The water reservoir elevation, H1 = 103.5 mThe tap elevation, H2 = 55 mThe diameter of pipe, d = 100…

Q: QUESTION 2 A vertical circular tank that is 1.5 m high, has sloping sides. The tank is 50 m and 30 m…

A: Given: The height of tank, h = 1.5 m The top diameter, D = 50 m The bottom diameter, d = 30 m The…

Q: a) An oil with a density of 870 kg/m³ and kinematic viscosity of 10.7 mm²/s flows at a rate of 0.1…

A: Oil density = 870 kg/m3Kinematic viscosity = 10.7 mm2/s Flowrate = 0.1 m3 /s Slope = 1 in 500

Q: A siphon consisting of a 2 cm diameter tube is used to drain kerosene oil from a large open tank.…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.