%3D Problem 13.1. The aluminum machine part is subjected to a moment of M = 75 N.m. Determine the bending stress at points B and C on the cross section. 20 mm 10 mm 20 mm 10 mm 10 mm 10 mm 10 mm M= 75 N-m 40 mm

Q: 2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A:

Q: 5 The supports of Beam AD are aluminum rod and st eel rod only. Determine the stress in the aluminum…

A:

Q: Q3 Answer either A or B: A. Determine the design moment strength of 3 No. 19 the section shown in…

A:

Q: Check whether the Euler's equation is appropriate or not. ) Determine the maximum distributed load…

A:

Q: 400 Material A 300 Material B 200 Material A 100 0.002 0.004 0.006

A: Solution: B) Given Data: Tensile load=88 kNElastic modulus of material A=150 GPaElastic modulus of…

Q: In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards.…

A:

Q: Problem 5: A rigid bar of negligible weight is supported as shown in Figure. If W = 100 kN, a)…

A: W = 100 kN = 60 MPa

Q: A hollow circular shaft has an external diameter of 120 mm and internal diameter 60 mm. if the…

A:

Q: Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal…

A:

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A:

Q: A 10 cm diameter solid alumin Assume that L=0.5 m. The yiel a) Normal stress due to bending caused…

A:

Q: 1.3 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the…

A: Determine the magnitude of the force P for which the tensile stress in rod AB has the same magnitude…

Q: A 200 kN force is applied at the free end of the cantilever beam as shown in the figure below. What…

A:

Q: Determine the stress in rod if tensile force applied of 23 N having cross sectional area of 50 mm2

A: Tensile force, T = 23 N Area, A = 50 mm2 now Stress = ?

Q: Problem 3: Put 32.5 into a steel tube 2.4 meters long, 34 mm radius and 1.5 mm thick. A circular bar…

A: Given, T= 900 Nm GS = 77 GPa GA= 26 GPa radius of steel = 34 mm thickness = 1.5 mm

Q: FIGURE 1 are applied at of steel, bronze rigidly attached together. If P = 3000 lb and the…

A:

Q: The beam shown in the figure below is subject to a moment of M = 17 kN.m as illustrated. Calculate…

A: Given:-  M = 17 kNm

Q: Bronze A= 400 mm? A = 600 mm? A= 300 mm? ЗР 2P 4P - 4 m -3 m- -5m-

A:

Q: 8.10 This is steel, consisting of 9 rods that are articulated together in the nodes. There is a…

A: Using equilibrium conditions, ∑H = 0HA = 0∑V = 0RA+RB = P∑M at A = 0P×2 = RB×4RB = P2Using the above…

Q: 150 mm с |B 6 mm 100 mm- i The beam has simple supports and an overhang and is subjected to a point…

A:

Q: 3. A solid aluminum shaft in 3 in in diameter is subjected to two torques as shown below. Determine…

A:

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: σ=PA     ----( 1 ) here σ is stress , A is cross sectional area and P is force applied Calculate σst…

Q: CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between…

A: NOTE: As per our company guidelines for multiple questions we need answer 1st question only

Q: 2. Two rods connected as shown carry a vertical load of 20 kN. Rod AB is a steel rod with E = 2 X10³…

A: Given data  EAB = 2 × 105 N/mm2  EBC = 7 × 104 N/mm2  LAB = 3m = 3000 mm  LBC = 2m = 2000 mm  A =…

Q: Using an Permissible stress of 155 MPa, determine the maximum bending moment M that can be applied…

A: Given,  An, I section beam, Allowable stress, σ = 155mpa Find out:- maximum bending moment,

Q: 960 mm 640 N 3 280 mm 360 N a. Determine the tension in segment AC b. Determine the tension in…

A:

Q: In the figure below is a slim, high-strength steel rule (E = 30X106 psi) having thickness 0.175 in.…

A:

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: ... Bronze A = 300mm² 2.00 m E = 83 GPa %3D Steel 1.00 m A = 600mm? E = 200 GPa A B 0.60m 1.00 m…

A:

Q: An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the…

A:

Q: A rigid bar of negligible weight is supported as shown below. Compute the value of the load W that…

A:

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: Determine stress in each section

Q: If the beam is subjected to an internal moment of M = 30 kN.m, determine the maximum bending stress…

A: Given : M = 20 kN-m This is a problem of Solid mechanics where we have to find the max. bending…

Q: determine the stress in each rod after the load after the load P = 30 kips is applied

A: Given- The light rigid bar ABCD as shown in figure is pinned at B and connected to two vertical…

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.