the selected option is not the answer A steel beam having a span of 9 m carries a concentrated service live load at the midspan.The beam has fixed support on the left side and a roller on the right side. Bending is aboutthe x-axis. Assume the beam to have continuous lateral supports and a compact section.Neglect the weight of the beam.Prop. of Beam SectionA = 24645 mm2d = 488.95 mmbf = 283.48 mmtf = 30.48 mmtw = 17.02 mmDetermine the value of the service concentrated live load P (in KN) based on the *shear strength. Ø = 1.0 Cv= 1.0171218751232Zx = 4769 x 10^3 mm^3Sx = 4195 x 10^3 mm^3Fy = 345 MPaE = 200000 MPa1566

Answered: Image /qna-images/answer/73a79b43-525f-4c2f-921c-a041a58d422d.jpg

Answered: peam has fixed support on the left side…

peam has fixed support on the left side and a roller on the right side. Bending is about -axis. Assume the beam to have continuous lateral supports and a compact section. ect the weight of the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The T-beam in the floor system has a slab thickness of 90 mm and supported by beams 6.5 m span. The beam is casts monolithically with the slab. The spacing of beams is 2 m on centers and width the web is 400 mm. The effective depth of the beam is 600 mm. It is reinforced at tension side with 8-28mm Φ bars. fc’ = 28 MPa, fy = 415 MPa 1. Which of the following most nearly give the effective width of the flange? a. 1565 mm b. 1305 mm c. 1275 mm d. 1625 mm 2. Which of the following most nearly gives the depth of compression block? a. 62.25 mm b. 52.86 mm c. 60.26 mm d. 58.29 mm 3. Which of the following gives the nominal moment capacity of the beam? a. 1461.25 kN/m b. 1156.36 kN/m c. 1163.15 kN/m d. 1172.58 kN/m
2 A simply supported beam has a dimension of 300mmw x 600mmh has a span of 6m. it has a superimposed load of 30KN/m and live load of 50KN. It has a specified concrete strength of 28MPa and yield strength of 420MPa. Distance of centroid steel area to outermost fiber is 60mm. a. What is the maximum moment of the beam? b. What is the required tension steel area? Use et = 0.004
Part 2 A Pratt roof truss is loaded as shown. Using the method of joints and the method of sections, determine the force in all members. the force P.171kN 80 kN P kN 60 kN H 8 m 60 kN A G- MATHalino.com 6 m C 6 m E 6 m 40 kN 100 kN 6 m
A beam cast monolithically with the slab thickness of 110 has a span of 4 m spaced at 6 m center to center. The width of the web is 300 mm and effective depth of 500 mm. It is reinforced on the tension side with 8-20 mm Φ rebars. Fc’ = 30 MPa fy = 310 MPa 1. Which gives the effective width of flange? a. 2000 mm b. 1500 mm c. 2500 mm d. 1000 mm 2. Which gives the depth of the compression stress block? a. 30.55 mm b. 32.56 mm c. 12.45 mm d. 42.14 mm
Example 2 of Method of Sections: Determine the force in member EB of the FBD of the roof truss shown in the Figure below. Indicate the member in compression (C) or in tension (T). 1000 N 3000 N 1000 N E 1000 N 2 m -2 m -2 m -2 m 4000 N 2000 N
Determine the design strength of the beam shown. Assume fy=345MPA and fc'=21MPa. 3-22 mm 75 375 mm 375 450 mm
Steel design
4. Determine the maximum tensile and compressive bending stress in the beam if it is subjected to amoment of M = 4 kip-ft.
A plane frame structure is shown as following figure El=1. Assuming that the inflection points are located at the middle height of the columns and the columns have the same lateral stiffness on each floor. Try to determine the beam end bending moments MA2 of beam A2B2 A₂ El-S By El-3 C₂ El=5 D₂ (55KN) Ele EL El hy 4m El=5 B₂ F₁- El-3C₂ EL-5 D (40KN) hy Sm EL El A₂ EL 4₂₁ B₁ Ele El D₁
SITUATION 1 Determine (approximately) the force in each member of the truss. Assume the diagonals can support either a tensile or a compressive force and assuming that the diagonals cannot support a compressive force. A. Use Method 2 7 k 14 k 14 k 7 k H F E 2k 6 ft D В 8 ft 8 ft 8 ft B. Use Method 1 50 kN 40 kN 20 kN | F E 3 m |B 3 m 3 m
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a=lm, b= 1.75m, d=50 mm, h= 6mm E D 2a b
Situation 4: A W530 x 92 simply supported beam has a length of 12 m. The beam supports a super imposed dead load of 12 kN/m and equal concentrated load of "P" at quarter points. The compression flange is laterally supported at point loads and the reactions. Use A 36 steel Fy = 250 MPa Properties of W 530 x 92 A 11800 mm² d = 533 mm bf = 209 mm tf = 15.6 mm tw = 10.2 mm rts 54.6 mm ry = 45.0 mm kdes 28.4 mm Sx = 2080 x 10³ mm³ Zx 2360 x 10³ mm³ J= 762 x 10³ mm³ Cw=1600 x 10⁹ mm 1. What is the maximum laterally unbraced length at which the nominal moment capacity maybe taken at FyZx?) 2. What is the allowable moment? use Cb = 1.4911 3. What is the allowable load "P" so that it will not exceed its allowable stress design ( 4. What is the allowable load P so that it will not exceed the allowable shearing stress? 5. What is the allowable moment if the beam is laterally support at supports only? Use 1.4911