Part2: Multiple power sources The circuit shown below was generated on MapleSIM 2019 R3 V2= 4V Vi= 5V 13 R2 R1 Figure 4: Circuit diagram using multiple power supplies and multiple loops In the above circuit, R1=502, R2=25N and R3=75N, The response of this circuit (Fig 4.), i.e., the values of the probes measuring currents was simulated for a total time of 10s. The simulated data is shown below S Analysis Window: Simulation Results Simulation Results Probe Plots Stored Results ili BlA "Multiple power supples atest Hesuts -0.015 -0.020 0.025 -0.025 0020 Vanables: Multple power supple. -0.030 0.015 -0.035 Find: 0010 Main -0.040 6 10 2 6. 10 12 0.055 V Plot Windows Multiple power su. 0.050 BlA Probe Plots ILI 0.045 0.040 0.035- Figure 5: Simulated current response for circuit shown in Fig 4.

Part2: Multiple power sources The circuit shown below was generated on MapleSIM 2019 R3 V2= 4V Vi= 5V 13 R2 R1 Figure 4: Circuit diagram using multiple power supplies and multiple loops In the above circuit, R1=502, R2=25N and R3=75N, The response of this circuit (Fig 4.), i.e., the values of the probes measuring currents was simulated for a total time of 10s. The simulated data is shown below S Analysis Window: Simulation Results Simulation Results Probe Plots Stored Results ili BlA "Multiple power supples atest Hesuts -0.015 -0.020 0.025 -0.025 0020 Vanables: Multple power supple. -0.030 0.015 -0.035 Find: 0010 Main -0.040 6 10 2 6. 10 12 0.055 V Plot Windows Multiple power su. 0.050 BlA Probe Plots ILI 0.045 0.040 0.035- Figure 5: Simulated current response for circuit shown in Fig 4.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3.-Calculate the electrical currents already indicated with their respective label in the circuit, that is, the currents in each branch 11= 12= 13= Note. The current 11 passes only through R1, and R3, 12 passes only through R4, and 13 passes through R2 and Rs. Draw the polarity to active, passive elements, nodes and meshes. R₁=2 Q ww V₁=10 V a V2=6 V ry R4=3 Q R3=4 Q R2=40 ww www b www V3=4 V R5=2 Q
In the circuit shown in the figure th .. .ammeters measurements are ..... Rs A 1500 R1 1500 so0 R4 it i2 i3 R2 500 R3 300 A E, = 20 V E2 = 24 V %3D 1.2 A, 0.7 A, 0.33 A O 0.12 A, 0.07 A, 0.33 A. O 1 A, 2.2 A, 0.48 A O 1.29 A, 0.7 A, 3.3 A O
[6] 14. Solve the unknowns for the following circuit. 1000 V 60 Hz www IT = R1 = 120 ohms VARS = www W = VA = C = 10 micro- farads R2 = 100 ohms P.F. = 20 = 450 ohms R3= 150 ohms
Plz what is the methods of this circuit. ALL methods Plz.
DC NETWORK ( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
Example:- For the following cct., I2=2 mA. Calculate :- a) All the remaining currents in all resistors. b)Supply voltage ET. c) Voltage Vab. HW R6-2.5K N c R4=15 KN a R1 5KN R3=20 KN e R2 20KN RS=1K N b d
Refer to the given circuit while noting that the same current flows through each element. The voltage-controlled dependent source provides a current which is five times as large as the voltage Vx. A 8 V + 5V For VR=180 V and Vx= 172 V, determine the power supplied by each element. (You must provide an answer before m next part.) The power supplied for Vx source is The power supplied for element A is The power supplied for 5Vx dependent source is kW. kW. kW.
A voltage-dependent voltage source 5V, is connected in series with Vs and a 50 resistor. Assume that the supply voltage Vs = 148.88V, calculate the supply current Is (in A) 50 V, + V. 5V.
the variable resistor in the circuit in (Figure 1) is acfusled for maximum power transfer to Ro. Suppose thatv=290 V. a) Find the numerical value of Ro . B) Find the maximum power delivered to Ro