Part K Calculate the reactive power for the following values. v = 100 cos(wt - 45°) V, i = 20 cos(wt +105°) A. Express your answer in volt-amperes reactive to three significant figures. [5] ΑΣΦ | 1 vec ?

Q: 4. B increases with - in temperature. A. decrease B. decrement C. no decrease D. increase E. no…

A:

Q: Often, the network is referred as an infinite bus when a change in input mechanical power or in…

A: In power systems many generator buses are connected together to form infinite bus.

Q: Q14: The arithmetic shifts right instruction ashr means divide the number by 2. Find the result of…

A: First 08 is loaded into the Acummulator in the form of binary. Given that ashr means divide the…

Q: could you please help me with item d please

A: Asked to find (d) The inductor current position with respective to inductor voltage? And what angle…

Q: Larut . For the type E chopper to be operated in the fourth quadrant only one switch is operated two…

A: In the IVth quadrant, only CH4 is capable of being operated, meaning it can be switched on and off…

Q: What is the difference between the pins under number 1 and the pins under number 4, and mention when…

A: The difference between pin 1 and pin 4 is the transmitting ability (information) to external…

Q: QUESTION 4 The following code is used as delay in a program: 0104 MOV BX, 0004 0107 MOV CX, FFFF.…

A: The address of the BX=0008H instead of 0004H.  When the loop is ON,  DEC is used here for…

Q: Table 1-4 4-Bit Reflected Code Reflected code 0000 0001 0011 0010 0110 0111 0101 0100 1100 1101 1111…

A: The other two codes we ca use are Hexadecimal code Binary code

Q: 3. Below is a nonlinear scale such as ones used for reading resistance on an analog meter. There are…

A:

Q: Duty: design a hand counter according to the following order from left to right 4, 5, 0, 1, 3, 7…

A: SEQUENTIAL LOGIC CIRCUITS: Sequential Logic circuits, unlike Combinational Logic circuits, have some…

Q: Please answer in typing format

A: Step 1:A rectifier is used to convert AC signal to DC signal.Working of half wave rectifierSince,…

Q: Which of the following statements about printed circuit boards is correct? O a. It can be single,…

A: PCBs are called as printed circuit boards. They are used as support for electrical and electronic…

Q: 4- In digital computer we considered the controlled buffers can be useful, why?

A: 4- Buffers are a type of register that can be used for storing binary words. The buffers are…

Q: Q1/The Gray code (10110111101)= ( ) in decimal number None of them O 1753 O 869 O 1749 O 931 O 1750…

A: We need to do convert the gray code to decimal number

Q: Question A differential protection scheme is shown below 400/1 80 A fooo I, 00000 F I₂ The…

A: Given- A differential protection scheme as shown. To Find- The percentage bias.

Q: The number of possible values for signals is restricted. a. Analog b. Digital c. Either (a) or (b)…

A: A digital signal is a signal which is represented as s sequence of discrete values.  In digital…

Q: For the following circuit find VL, IL, Iz and IR if RL = 180 , repeat for R₁ = 470 R$ 20 V 220 2 Vz=…

A: Given: Circuit diagram,

Q: What is electrical sub station?

A:

Q: Determine the take-up and measurement to your mark for each of the following. Length EMT Size…

A: According to the question, we need to calculate take-up and mark for the given EMT size.

Q: 32K×4 A14 En • CS

A:

Q: Full load copper losses

A:

Q: What would be the result of the following expressions in MATLAB command prompt: 6 - 2 * 15- 32

A: The given command prompt is: 6-2*15-32

Q: for what purpose the adders are used in digital systems i.e. full and half adders?

A: Firstly We need to Know What is an ADDER:- In Digital Electronic Adder is a Combinational Circuit…

Q: 011010, carry=0 011110, carry=0 p01011, carry=1 011110, carry=1

A:

Q: Give the value of the following resistors: (Must write final value to short notation using KOhms,…

A: Given :- In this question we have to used following table for respective color. For 4 band…

Q: 4. Below is a nonlinear scale such as ones used for reading resistance on an analog meter. There are…

A: Since you have posted a question with multiple sub parts , we will solve first three sub parts for…

Q: Consider a step down converter supplied by a DC power source of magnitude Vs = 220 v. The switching…

A: Rectifier: Because nearly every electrical appliance runs on DC (Direct Current), the rectifier…

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: Calculate the output for the given circuit. R2 R2 Voo ww R1

A: R1=250.6 ohm R2=978.86 ohm Vc=7.4Vo=4.7Here it is inverting amplifier gain is -R1R2R2 → feedback…

Q: Explain unbiased p-n junction by drawing figures.

A: Below is the solution

Q: 00010101 b) Ob00110100 & 0b10010100 = 0b c) Obl1010010 ^ Ob10010100 = 0b %3! + 10010110

A:

Q: Solve for ID in IMG 18 V 2kQ 1100 mA. round off your answer with 1 decimal value V-1.7 V 0.51 k

A: FET are voltage controlled device. BJT is current controlled device JFET is stand for Junction field…

Q: (3-a) Is this an analogue or digital electronic problem? Explain the difference.

A: It is a digital electronic problem

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.