▾ Part H The beam is supported by the roller B and the rocker C and contacts the smooth plane at A. Draw the free-body diagram for the beam. Draw the vectors starting at the black dots. The location and orientation of the vectors will beeoluded. The length of the vectors will not be graded. + E 0 NA reaction at A By reaction at B ected Cy reaction at C L. گئے 4 m- 500 N -2m-+- 800 N 60° -6 m

▾ Part H The beam is supported by the roller B and the rocker C and contacts the smooth plane at A. Draw the free-body diagram for the beam. Draw the vectors starting at the black dots. The location and orientation of the vectors will beeoluded. The length of the vectors will not be graded. + E 0 NA reaction at A By reaction at B ected Cy reaction at C L. گئے 4 m- 500 N -2m-+- 800 N 60° -6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculat reactions at pin support A and edge B, take beam weight 35 Kg 1 т 3 т B 50° A
Hiw the cross- Sectional dimensiuns of a beam are shown below. If the makimum allowabhe benehing stresS 600 Mpa. Determine the mx imum beneliny ma gnitude (M) thut Can be suppurtel by the beam. Supporn the syn is ef bending is positive. 75mm 1% mm Hw:: A beam had subjected to a postive bending moment of 5 KN. m. The Cross-Sedional dimensions are shown below. Draw the bending stress distribution on the Cross- Sedion. loo mm 15 mm 15a wm 13 mm
Kindly give me both C and D right answes
1. Classify each of the structures shown in the figure as externally unstable, statically determinate, or statically indeterminate. If the structure is statically indeterminate externally, then determine the degree of external indeterminacy. Hinge Hinge a. C. DANIE BO B Coordinovan) SONHNISH Hinge WARRAS HARRAS Hinge Hinge b. DAMEN OVOŠÁRTÁTNOBITAKACHO Hinge for CANE
A compound beam as shown with a pin at A, a hinge at C, and rollers at B and D,1) Draw all F.B.D.s for your calculation;2) Determine the reactions at A, B and D when the beam is in equlibrium [Hint: 1) ABC part is the independent part and CD is the dependent part of the compound beam. The analysis always starts from the dependent part, then the independent part. 2) Draw the FBD of CD part first.]
Two rods of diameter d = 3 in are joined together: a C83400 brass rod, and a %3D 2014-T6 aluminum rod. The length of the brass rod is L1 = 2 ft, and the length of the aluminum rod is L2 = 3 ft. A force of magnitude F = 422 Ibf is %3D %3D %3D exerted on the assembly at a distance of L ft from A. Determine the magnitude of the reaction force at A. Express your answer in Ibf. B. F L2
Statically Indeterminate Problems
3) A load of 2,700 N acts on the machine part shown below. The machine part has a uniform thickness of 12 mm. Note: Point H will not be used in this problem and may be disregarded. a) Draw an FBD at showing the internal forces present at K. You may choose which side of the part to cut off. One method means you must find reactions at A and B. Choose the method that seems easier to you. b) Calculate the normal and shear stresses at point K (in MPa). [Ans. to check: = 0; ay = -10.89 MPa; Txy=-6.85 MPa] c) Draw the stress element at the point located at K. d) Calculate the normal and shear stresses if you rotate the element -20°. Draw a properly oriented stress element. 2,700 N 135 mm 60° C 50 mm 75 mm 50 mm X 40 mm # 12 mm 15 mm PH 40 mm OK y
Can you please show me the full solution of Rah and RAV in the reactions and the PAB, PAC, PBD, AND PCD in the member of forces?
Solid.mech.som problem.
choose the correct answer
THEORY OF STRUCTURES PLEASE PROVIDE COMPLETE SOLUTION THANKS