Part A What radius must a water drop have for the difference between the inside and outside pressures to be 0.0213 atm ? The surface tension of water is 7.28x10-2 N/m. Express your answer in meters. R = Im Submit Request Answer

A container of water has a cross-sectional area of A=0.1m2 . A piston sits top of the water (see be following figure). There is a spout located 0.15 m from the bottom of tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spat is As=7.0104m2 . (a) What is the velocity of the water as it leaves the spout? (b) If the opening of the spout is located 1.5 m above the grand, how far from be pout does water hit the floor? Ignore friction and dissipative forces.

(a) Using Bernoulli's equation, show that be measured fluid speed v for a pitot tube, like the one in figure 14.32(b), is given by v=( 2gh)1/h , where h is be height of be manometer fluid, p' is the density of the manometer fluid, p is the density of the moving fluid, and g is be acceleration due to gravity. (Note that v is indeed proportional to the square root of h, as stated in text) (b) Calculate v for moving air if a mercury manometer's h is 0.200 m. Figure 14.32 Measurement of fluid speed on Bernoulli’s principle. (a) A manometer is connected to two tubes close together and small enough not to disturb the flow. Tube 1 is open at the end facing the flow. A dead spot having zero speed is created there. Tube 2 has an opening on the side, so the fluid has a speed v across; thus, pressure there drops. The difference in pressure at the manometer is 12v22 , so h is proportional to . 12v22 (b) This type of velocity measuring device is a Prandtl tube, also known as a pitot tube.

A straightforward method of finding the density of an object is to measure its mass and then measure its volume by submerging it in a graduated cylinder. What is the density of a 240-g rock 89.0 cm3 of water? (Note that the accuracy and practical applications of this technique are more limited than a variety of others that are based on Archimedes' principle.)

Archimedes' principle can be used to calculate the density of a fluid as well as that of a solid. Suppose a chunk of iron with a mass of 390.0 g in air is found to have an apparent mass of 350.5 g when completely submerged in an unknown liquid. (a) What mass of fluid does the iron displace? (b) What is the volume of iron, using its density as given Table 14.1? (c) Calculate the fluid's density and identify it.

Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?

Blood is pumped from the heart at a rate of 5.0 L/min into the aorta (of radius 1.0 cm). Determine the speed of blood through the aorta.

Suppose you have a coffee with a circular cross-section and vertical sides (uniform radius). What is its inside radius if it holds 375 g of coffee filled to a depth of 7.50 cm? Assume coffee has the same density as water.

What is the difference between flow rate and fluid velocity? How are they related?

A spherical weather balloon is filled with hydrogen until its radius is 3.00 m. Its total mass including the instruments it carries is 15.0 kg. (a) Find the buoyant force acting on the balloon, assuming the density of air is 1.29 kg/m3. (b) What is the net force acting on the balloon and its instruments after the balloon is released from the ground? (c) Why does the radius of the balloon tend to increase as it rises to higher altitude?