Part A Hydrogen gas is produced when zinc reacts with sulfuric acid: Zn(s) + H₂SO4(aq)→ZnSO4(aq) + H2(g) If 163 mL of wet H2 is collected over water at 24 °C and a barometric pressure of 98.1 kPa, how many grams of Zn have been consumed? (The vapor pressure of water is 2.984 kPa.) m = 10 ΑΣΦ Submit Request Answer Provide Feedback ? g Next >

Part A Hydrogen gas is produced when zinc reacts with sulfuric acid: Zn(s) + H₂SO4(aq)→ZnSO4(aq) + H2(g) If 163 mL of wet H2 is collected over water at 24 °C and a barometric pressure of 98.1 kPa, how many grams of Zn have been consumed? (The vapor pressure of water is 2.984 kPa.) m = 10 ΑΣΦ Submit Request Answer Provide Feedback ? g Next >

Cornerstones of Cost Management (Cornerstones Series)

4th Edition

ISBN:9781305970663

Author:Don R. Hansen, Maryanne M. Mowen

Publisher:Don R. Hansen, Maryanne M. Mowen

Chapter15: Lean Accounting And Productivity Measurement

Section: Chapter Questions

Problem 28P

See similar textbooks

Similar questions

At -8.64 °C the concentration equilibrium constant K = 7.7 for a certain reaction. Here are some facts about the reaction: -1 • The initial rate of the reaction is 5.3 mol·L¯¹·s¯¹. . If the reaction is run at constant pressure, 132. kJ/mol of heat are absorbed. • The constant pressure molar heat capacity C = 2.97 J'mol K¹. Yes. Using these facts, can you calculate K at 16. °C? x10 O No. If you said yes, then enter your answer at right. Round it to 2 significant digits. If you said no, can you at least decide whether Kat 16. °C will be bigger or smaller than K at -8.64 °C? C Yes, and K will be bigger. Yes, and K will be smaller. No.
One kg of water within a piston-cylinder assembly executes a Carnot power cycle. During isothermal expansion, the water is heated from a saturated liquid at 50 bar until is a saturated vapor. The vapor then expands adiabatically to a pressure of 5 bar and a quality of 0.8291. a) Sketch the cycle on P-v and T-s diagram. b) Evaluate the heat transfer and wor for the above processes (isothermal expansion and adiabatic expansion) c) Evaluate the thermal efficiency.
A mixture with the system given below is fed to a flash distillation column operating at 20 bar and 70 C. Calculate the compositions and flow rates of the streams leaving the column. components Amount (kmol/h) ethane propane N-butane i-butane n- pentane 15 25 25 15 20
please don't provide han writing solution
Estimate the laminar flame speed of a stoichiometric Benzene-air mixture. Given that: Fuel: Benzene CHб Average reaction rate = -2.25 kmol/s-m³ MW air =28.84 kg/kmol pu (at 300k) = 1.16 kg/m³ Use air properties to evaluate the thermal diffusivity -> i BI III ☑ US X2 x²
C (Ib/gal) - 5.8. A mixing process may be described as follows: A stream with solute concentration Ci (pounds/volume) is fed to a perfectly stirred tank at a constant flow rate of q (volume/time). The perfectly mixed product is withdrawn from the tank, also at the flow rate q at the same concentration as the material in the tank Co. The total volume of solution in the tank is constant at V. Density may be considered to be inde- 2.1 2.0 1.9 1.8 1.7 W FIGURE P5-8 10 6:30 A.M. Time 6:52 A.M. pendent of concentration. A trace of the tank concentration versus time appears as shown in Fig. P5-8. (a) Plot on this same figure your best guess of the quantitative behavior of the inlet concentration versus time. Be sure to label the graph with quantitative infor- mation regarding times and magnitudes and any other data that will demonstrate your understanding of the situation. (b) Write an equation for C; as a function of time. Data: tank dimensions: 8 ft high by 5-ft diameter Tank volume V: 700…
1. A protein chromatography column that processes 15 kg of protein in 60 h, is cycled every 6 h, can be loaded with 10 grams of protein per liter of column volume, has a maximum flow rate of 50 liters/ min at a pressure of 4 bar, and is packed with an incompressible resin having a particle diameter of 90 μum and void fraction of 0.35. The viscosity can be assumed to be that of water. i. What are the dimensions required for the column? ii. If the flow rate is 1 column volume per minute and the pressure rating is still 4 bar, what column dimensions are required? Is the resolution equivalent to that for Part (i)? 111. If the pressure rating for the column were raised to 12 bar, should the column dimensions change? Is so, what should the dimensions be? Do they make sense? iv. What is the best way to increase the productivity of the column packing?
typing clear urjent i will give 5 upvotes
1. The projection of the liquidus surface of the ternary system A-B-C is given below; a) Draw the isothermal sections at 400°C and room temperature. (20p.) b) For composition X, what is the amount and composition of solid phase at its solidus temperature? What would you suggest to increase its amount by keeping temperature constant? (20p.) A (705°) B (924°) A.B 569° 547° 850 650- X 550- 513 $450 460° 550 500 484° 400° 500- 550- -650- 600- 750- Yo A3B2C 2B.C 736° 683° B.C wt.% 660° A3C 580° A6C (684°)
100 mL of a 0.1 M solution is titrated with 50 mL of 0.1 M NaOH. The new solution has a pH of 4.75. Upon addition of 10 mL more of 0.1 M NaOH, the pH of the solution is 5.00. a. What is the identity of the original 100 mL 0.1 M solution? HCI O NaOH O acetic acid water KOH
None
A mass of 5 kg is attached to a spring with spring constant 25N/m. The mass is acted on by an external force of 10 sin(t) Newtons and moves in a medium that imparts a viscous force (i.e. friction) proportional to the velocity with constant 10Ns/m. If the mass is set in motion from its equilibrium position with an initial velocity of 60 cm/s, formulate the initial value problem describing the motion of the mass. Then solve this initial value problem. HINT: watch out for the units! Centimeters are not meters!