Part 3: Reversibility of hydration 1. Transfer a small amount of solid copper (II) sulfate pentahydrate, CUSO,-5H,O, that just fills the bottom of a clean, dry 150-mm (medium size) test tube. 2. Using a test tube holder, grasp the test tube containing the hydrate and heat over a Bunsen burner flame while holding the test tube at a 45° angle. 3. While heating, closely observe the solid and the inside wall of the test tube. Record your observations. 4. When the solid residue seems to be completely dehydrated, allow the test tube to cool completely. Then, add a few drops of laboratory water to the solid in the test tube. What changes did you see? Record your observations. Appearance of CUSO..5H2O: Appearance of solid after heating: Appearance of the inside wall of the test tube after heating: Appearance of solid residue after adding a few drops of laboratory water:

Part 3: Reversibility of hydration 1. Transfer a small amount of solid copper (II) sulfate pentahydrate, CUSO,-5H,O, that just fills the bottom of a clean, dry 150-mm (medium size) test tube. 2. Using a test tube holder, grasp the test tube containing the hydrate and heat over a Bunsen burner flame while holding the test tube at a 45° angle. 3. While heating, closely observe the solid and the inside wall of the test tube. Record your observations. 4. When the solid residue seems to be completely dehydrated, allow the test tube to cool completely. Then, add a few drops of laboratory water to the solid in the test tube. What changes did you see? Record your observations. Appearance of CUSO..5H2O: Appearance of solid after heating: Appearance of the inside wall of the test tube after heating: Appearance of solid residue after adding a few drops of laboratory water:

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

He has a sample that weighed 0.03 g of NaCl and dissolved it in 250.00 mL, he is going to titrate it with a 0.1M AgNO3 solution. How many mL of AgNO3 must you approximately discharge to form the solid? Data:- MM NaCl: 58.4 g/mol- MM AgNO3: 169.87 g/mol- MM AgCl: 143.32 g/mol
A student determined the concertration of NaOCI in a commercial bleach sample using the same technique described in section "F" of the Halogens and Their Compounds lab. The student required 18 drops of 0.01M Na25203 to reach the end point. What is the concentration (reported in percentage) of NaOCI in the bleach sample?
The purpose of adding an excess of the precipitating agent is: 1- Ensure that the sedimentation is complete 2- Get big crystals 3- Purification of the precipitate 4-Prevent pollution
What do the ions that gave a precipitate when mixed with AgNO3 have in common? Hint given: Identify the ions and the Group of the Periodic Table to which they belong
Perform the necessary calculations for the preparation of: a) 200 mL of AgNO3 0.50 M from the solid reagent b) 1 L of HCl 0.25 M and N, consider the purity and density of the acid to perform the calculations c) 100 mL of potassium dichromate K2Cr2O7 (294.185 g/mol) 0.2 N
Please provide only typed answer solution no handwritten solution needed allowed
15. Which of the following co-precipitates is minimized by washing? a. Mixed-crystals b. Adsorbed impurities c. Mechanically entrapped particles d. Occluded particles 16. Which is NOT a strong acid? a. Muriatic acid b. Hydrochloric acid C. Perchloric acid d. Nitric acid
In order to keep as much HCHO dissolved in the water in the embalming machine reservoir as possible, the dilution water should be ___. Hot Cold
What is wrong with this setup? buret acid of unknown concentration base of known concentration stopcock The buret needs to be filled with more base The tip of the buret is not placed inside of the flask The buret is not supported by clamp Nothing is wrong with this
Which of these is NOT true of a good recrystallization solvent? Which of these is NOT true of a good recrystallization solvent? a) The compound is insoluble in the solvent when it is cold. b) The solvent boiling temperature is at least 40 °C. c) The solvent has many impurities. d) The compound is soluble in the solvent when it is hot.
#2 Calculate the volume you must dilute to make 260.0 mL of 0.50 M BaCl from 4.0 M original stock solution.
Calculate final MgCl2 concentration in mM for tube 2 and 3.