PART 3 1. Connect the circuit of Figure (2), the output of the power supply (20). 2. Slowly increase the supply voltage until E=20V , this voltage must remain constant, change the load resistance and record Vi, li, Iz, Rz, in table (3). 6802 100-10KO 20 V Figure (2) 5 ELECTRONIC LAB. EXP 6 LECTURER: MUSTAFA Y.AL-NAELI E(v) RL(Q) VL (v) L (mA) Iz (mA) 200 400 600 800 1K 20 1.5 K 2 K 4K 6 K 8 K 10 K

PART 3 1. Connect the circuit of Figure (2), the output of the power supply (20). 2. Slowly increase the supply voltage until E=20V , this voltage must remain constant, change the load resistance and record Vi, li, Iz, Rz, in table (3). 6802 100-10KO 20 V Figure (2) 5 ELECTRONIC LAB. EXP 6 LECTURER: MUSTAFA Y.AL-NAELI E(v) RL(Q) VL (v) L (mA) Iz (mA) 200 400 600 800 1K 20 1.5 K 2 K 4K 6 K 8 K 10 K

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ng to anouier question will Save uiIS fesponse. uèstion 12 For the following circuit, as we increase the load resistance R, the diode current I, increases. ID + Vo- Vs BRL True False A Moving to another question will save this response. hp
in atransistor circuit load resistance is 6kohm and quiescent current is 1.5mA.determine the operating point when the battery voltage Vcc =12.how will the q point change when the load resistance is changedfrom 6kohm to 10kohm
Instructions Calculate the DC voltages and currents in the circuit. Find for the current emitter, collector current and collector voltage. +12v 5kN 5kN Voz Vor Q2 Q1 Viz VE 2.7kN
:A-A base current of 1.25 mA is applied to the transistor in Figure 3 , and a voltage of 6.5 V is dropped across the resistors Rc. The voltage of 5 V is dropped across the emitter resistance RE, and the voltage across the transistor is 160 mV. Determine the Bpc of the transistor, IE, Vcc and VBB VCC Rc 100 Figure 3 RB VBE
Please answer all subparts
The power dissipated by the zener diode for the circuit of Figure is greatest when: (a) The zener diode is shorted. (b) The load resistor is removed. (c) The load resistor is shorted. (d) The input voltage is increased.
N
Please answer A B and C.. Its all a question
If v1 = -40sin(377t + 30°) V and v2 = 30sin(377t + 60°) V, which of these statements are true? (Note: V2 lags V1 by 90° out of phase V2 leads V1 by 90°out of phase V1 leads V2 by 150° out of phase O V2 lags V1 by 30° out of phase
Determine the voltage across the resistor R2. (assume Zener voltage is 3 volts and Diode forward voltage is 0.7V)
For the diode circuit of the figure below: 1. Determine v, and sketch its waveform for at least 4 cycles 2. Determine the average (dc) voltage established the load Show the details of your work. Without a complete solution (step-by-step solution) will invalidate your answer. 120 V 2.7 kN -120 V
i. Show that the power factor for a controlled full-wave rectifier with a resistive load is 1 sin(2a) + pf = -