Part 1: Process Diagram for Open-Loop Control SystemsAn open-loop control system can process an input condition to produce an output. Fill in the controller and theplant for each process shown below.InputControlOutputControllerPlantLight On,ControlLight OnToastedBreadToastedBreadControlWhat can be added in the process diagrams to verify the desired output has been achieved?

Answered: Image /qna-images/answer/51f4d70c-117b-46b6-b471-bd45c2e7d25e.jpg

Part 1: Process Diagram for Open-Loop Control Systems An open-loop control system can process an input condition to produce an output. Fill in the controller and the plant for each process shown below. Input > Controller Control Output Plant Light On Control. Light On Toasted Bread Toasted Control Bread

Part 1: Process Diagram for Open-Loop Control Systems An open-loop control system can process an input condition to produce an output. Fill in the controller and the plant for each process shown below. Input > Controller Control Output Plant Light On Control. Light On Toasted Bread Toasted Control Bread

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 1RQ: What is the advantage of using solid-state devices in electronic control systems?

See similar textbooks

Similar questions

List some instrumentation and controls-related research titles or topics. (Not using PLC/ARDUINO).
the controlled signals in control BD are then going to Select one: a. actuators b. sensors C. plant d. controllers the actuator requires a much higher primary voltage than 150v is Select one: O a Capacitive Discharge Ignition (CDI) O b. Inductive (Smart) O C. Peak and Hold O d. Inductive (Dumb)
please answer fast need it
Name each curve in terms of control mode in the following graph. And discuss the advantages and disadvantages of each mode. Add the on/off control curve to graph. y Set point Time
PROCESS INSTRUMENTATION AND CONTROL 6. Compare and contrast the Closed and Open loop Control System
Ans fast please
Suppose you are an electronic circuit designer. How you can use the center-taped step down transformer in bridge rectifier circuit?
Describe what is meant by sequence control.
1. For the ADC0804 used in section 1. the step size can be adjusted by setting the reference voltage on pin 9. When this pin is not connected (as shown in the figure 1 schematic), the reference voltage is the operating voltage Vcc. a) What is the step size for this default setting? b) How can we set the reference voltage on pin 9. to 4 V? c) What would be the step size after changing the reference voltage to 4 V? 2. Determine the analog input that will result in an output code of "10001110". Assume 5 V reference. Show your calculations. 3. What value of the analog input voltage would result in a digital output is 6F (hex)? Assume 4V reference. Show calculations. 4. In section, you used a 8-bit D/A converter. With a reference voltage of 5 V, what voltage does each bit represent in terms of the analog output? Show calculations. 5. For the D/A converter, if the output is 3.62 V, what is the value of the digital input? Show calculations. 6. For the D/A converter circuit shown in Figure 2,…
A 1-p On-Off AC voltage controller supply voltages of 440 volts and the output obtained is 220 volts. The number of Off cycles is 75. Find the number of On cycles. 50 25 O 100 O 75
a) Identify the type of control system shown in given figure .Also define the type of control system. + COMPARATOR DESIRED TOAST QUALITY - RELAY TO CONTROL TOASTER ACTUAL TOAST QUALITY HEATING TIME ERROR TOAST QUALITY MEASURING DEVICE FEEDBACK PATH b) Identify the following elements from the given block diagram. i)Measurement Element ii)Process Element iii) Final Control Element iv)Control Law and Implementation element. Control signal Achieved temperature Controlled Output Reference Valve Steam flow Tank Input Pressure thermometer
Write a report on system control strategies and techniques used in engineering.