Parabolic-louvered fluorescent luminaires have spacing coefficients of 1.4/1.1. They are mounted 10 ft above the floor. The work plane is 28 in from the floor. Determine the maximum center-to-center spacing (in f

Q: Point A is in between B and C, the distances of B and C from point A are 1.5km and 2.2km…

A:

Q: SECTION +A DRAWN BY: Point AB А с D E F G H I J K L X O O <-5 <-5 -10 -10 2 6 6 3 3 O Coordinate Y O…

A:

Q: Choose the correct x coordinate value for the for the rectangle " EGKJ " shown in Figure below A50…

A: We have to find x coordinator

Q: Using the Cartesian coordinate system, determine the absolute value of the distance y (in mm) from…

A: GIVEN DATA A COMPOSITE FIG GIVEN WE HAVE TO CALCULATE Y COORDINATE OF FIG

Q: 12. Depicted below is the side-view sketch of a breakfast bar/shelf that I built several years ago.…

A:

Q: Let s be the length of each side of each tile in a cubic regular tiling of the sphere. What is cos…

A:

Q: How do you calculate the location of the centriod? What's the shape and symmetric?

A:

Q: 100 mm 20 mm [4] 400 mm 360 mm 20 mm 20 mm 150 mm

A:

Q: Find the centeroid of the shaded area ?.shown in fig

A:

Q: 120 mm 160 mm 60 mm 80 mm - 140 mm 100 mm

A: Divide the shaded area into basic elements as shown above

Q: Using the Cartesian coordinate system, determine the absolute value of the distance x (in mm) from…

A:

Q: (Extra) Prove that for a spherical mirror: a) So=f(MT-1) /MT b) Si = -f (Mr-1) %3D

A:

Q: Find the centeroid of the shaded area ?.shown in fig

A:

Q: If the direction cosines for the satellite antenna shown are to be cosex = 0.286, cosły= 0.429, and…

A: The direction cosine of antena are

Q: IDENTIFY the Isometric projection of the orthographic projection shown below. Choose the correct…

A: According to the details provided in the question.we need to find Isometric view of the object that…

Q: 21. One of the following surface plate show that surface is flat at one end but becomes increasingly…

A: Given: Let us consider the given figures, To find: One of the following surface plates depicts a…

Q: Draw the three Views and a section elevation:

A: Required all three views Elevation, Right Hand Side View, Plan and Sectional Elevation are drawn…

Q: Coordinates of point P are given in the XY system. Calculate its coordinate in the UV system if the…

A:

Q: DRAW ON AN A4 SIZE SHEET AND CAPTURE FULL IMAGE Draw isometric view of a square prism with 20 mm…

A: Isometric view is the graphical representation of two-dimensional view into three-dimensional view.…

Q: On one side of a diverging lens of focal length 37.1 cm, you position an object of height 2.42 cm…

A: To choose: The correct answer. Given: The focal length of the diverging lens is f=37.1 cm. The…

Q: 8.07 60 45

A: 3D view

Q: 3. On the part below, specify a geometric control to make the left surface in the front view…

A: The geometric control that we need to specify to make the left surface in the front view…

Q: Given the line e = XY and the point F. Construct the cube ABCDA,B,C,D, if its edge AB lies on e and…

A: Given the line  e = XY  and the point F. Construct the cube ABCDAxBxCxDx, if its edge AB lies on e…

Q: Determine the centeroid of the shaded area ?shown in fig Dimensions in mm 45 20 100

A:

Q: Draw an isometric view of hexagonal prism of side 40 mm and height 60 mm.

A: Step1: The hexagon must be drawn inscribed in a square. Here all the sides of the hexagon measure 40…

Q: 20 points Determine the centroidal y-coordinate (in mm, round=off to 2 decimal places) of the plane…

A:

Q: Locate 7 ard j Y The shaded area' (41 ard f2)

A:

Q: Which of the following optical polygon combinations would be required to calibrate a rotary table at…

A: Calibration is the process of setting up an instrument such that it can deliver a result for a…

Q: Apply geometric tolerancing to part according to the instructions below. This exercise will provide…

A: The asked all three questions are answered and are marked in the image below clearly please refer to…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.