Pan = 96 kPa P=100.58 kPa h=? SG = 0.85

Q: Find fr (modulous of rupture) = ? M, bending moment = ? k = ? j = ? y = ? I = ? 0

A:

Q: Natural Channels conditions: Gravel beds, straight Gravel beds plus large boulders Earth, straight,…

A: Given data: Top width, B=500 m River depth, y=2 m Bed slope, S=0.01 mm For gravel beds, straight, n=…

Q: 2) Determine the moment of Area of the given Built-up section about its centroidal axis.The top…

A:

Q: 3. FIND PA -PB IN PASCALS IL 75 mm 5,6,= 0.8 OIL FROM C TO O 225 m 300 mm WATER 150 mm ELSEWHELE…

A:

Q: 2) Determine the moment of Area of the given Built-up section about its centroidal axis. The top…

A:

Q: What is the largest safe torque can be applied to the entire structure? (Provide answer in whole…

A:

Q: 2) Determine the moment of Area of the given Built-up section about its centroidal axis.The top…

A:

Q: To be classified as hollow, the unit must have what percentage voids? a. between 25 and 60 b. >60 С.…

A:

Q: For the circular arch shown in the figure, compute the value of "P"such that the vertical defiection…

A:

Q: What is A = Asector - Atriangle? Where did they get that?

A: Diameter= 500mmslope= 1500Q=0.04m3/sn=0.013

Q: A RA 3m 5-fon E 3m B Ro 4-don 1.5m Ace to qus RA - RB ⇒ I found the value of [x = 1.8m But I am co…

A: Given, x= 1.8m RA=RB Draw the fbd:-

Q: Define the Purkaystha and Char reduction factor method ?

A: The purkaystha and char reduction factor is used to find bearing capacity of foundation on…

Q: Q6• For figure below, caleulate the forces Surfaces on A f B. surface 8 (area = o-1m²) 0.1 air 2 w…

A:

Q: a 39 3i Blet A= d and B=2a+d 2b+e 2e+5 e g h i e Suose that det A = -3 , Evaluate the deteiminant of…

A:

Q: Determine the 4 storey period and modal matrix.(Derive) (i need the RED CIRCLED) P.S.An example is…

A: The objective of the question is to determine the period and modal matrix for a 4-storey building…

Q: #2 d=37 cm 17 3#8=15cm² = A's -4#11 =40cm² = As fc=280 Kleur fy=4200 kg/au- bw=40cmt Determine pun…

A:

Q: 2m 1.5m 2m 2m DE 2m C 3 kN 8 kN What is the value of B2? Round off to two decimal places. B.

A: Figure is as shown

Q: Calculate the required area of the colwen, Ag Given data: t'é t₁ = 4 ksi = 60 ksi fy Assumed…

A: Factored load, Reinforcement ratio,

Q: The four forces are applied to a rectangular block as shown below. Determine the magnitude of the…

A: To find magnitude of resultant couple

Q: What is the estimated SN of the data given? (1 Decimal point) Your answer

A: Structural number: It is an index that indicates the strength of the pavement layers as well as the…

Q: weight of the block?

A:

Q: 2. A stone A is dropped from rest down a well, and in 1 second another stone B is dropped from rest.…

A:

Q: A Find the equation for the internal shear in the beam from B to C in terms of x given: w = 10 kN/m…

A: Given data:- w=10 kN/mMD=5 kN-mLAB=3 mLBC=2 mLCD=3 mBy=56 kN (upward)Dy=6 kN downward

Q: Example 10.1: - SP and Resistivity (shallow and deep) logs are shown in Figure 10.1 in front of…

A: Without any applied current, the spontaneous potential log (SP) quantifies the natural or…

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A:

Q: For the beam shown, the magnitude of the concentrated load is P = 11 kN, the magnitude of the couple…

A:

Q: Find the percent finer of each sieve.

A: % finer for each sieve =Total wt-Cumulative wt retained upto that sieveTotal wt% finer for sieve 4…

Q: Define e-Log-p Method

A: Pre-consolidation pressure is the maximum lateral pressure that has been experienced by the soil…

Q: 3. Determine the inverse of the matrix A. 5 3 -4 A = 3 8. -2 -4 -2 7

A:

Q: Properties A = 14581 mm² d = 269.24 mm bf = 258.83 mm tf = 22.10 mm tw = 13.46 mm Sx = 1408 x 10³…

A: Solution: Given: Service dead load = 23.44 kN/m point load acting at the center, since the load is…

Q: A =? P= ? T= ? 17.0 m 7.0m 0.90 m 3.0m

A:

Q: Question 1: A sheet pile wall isolates two flooded areas as shown in Figure 1. The head loss ÿH…

A: As per guidelines we need to answer only first question so please repost rest questions separately

Q: What are the parameters in designing flexible pavements? *

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: P/A and (oalalow MJAr? (os)aller 54000 If it is pinned at its top and bottom, and a compressive load…

A: Solution  Given that (σb)allow=21 ksi

Q: Using the design chart below. Estimate the SN if W18=10x10^6, R=90%, So=0.35, Mr- 10000Psi, APSI=3.…

A: Design Structural number(SN) is a parameter of overall structural characteristics, which are…

Composite Construction

Composite construction is the construction of structures in which two or more materials are used. Regarding structural engineering, composite construction is a construction where two materials are bound together in a technical manner such that both the materials act as a single unit to carry and transfer the load. The motives of composite construction are to increase the structural strength, make structures more aesthetic, and provide a sustainable environment.