P5.17 An engineer determines that a 40 cm long rod of 1020 grade steel will be subjected to a tension of 20 kN. The following two design requirements must be met: the stress must remain below 145 MPa, and the rod must stretch less than 0.125 mm. Determine an appropriate value for the rod's diameter to meet these two requirements. Round up to the nearest millimeter when reporting your answer.

P5.17 An engineer determines that a 40 cm long rod of 1020 grade steel will be subjected to a tension of 20 kN. The following two design requirements must be met: the stress must remain below 145 MPa, and the rod must stretch less than 0.125 mm. Determine an appropriate value for the rod's diameter to meet these two requirements. Round up to the nearest millimeter when reporting your answer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A block of with edge lengths 8.30 m. 3.20 m, 4.50 m sits on top of a pillar with a square cross section of edge length 23 cm. If the stress on the pillar is 50.5 MPa. find the density of the block in g/cm3. Round your answer to 1 decimal place.
Q2. What is meant by major stresses and major levels? b An element in a plane affected by the stresses shown in the figure using the arithmetic and semi-graphical method. Calculate 1- The main stresses and their trends or levels on which they are located. - The greatest shear stress, the plane on which it lies and the associated vertical stress. - Vertical stresses if the element rotates at an angle of 20 on the main plane. B 5.000 psl 4.000 psl 15,000 psl veroo
EXERCISE 1)Define the diameter of a wire used for lifting an elevator of 1000 kg.The wire material has a yield strength of 240 MPa.
The state of stress shown to the left was produced by a combination of loadings on a body that is not shown. Determine the following via Mohr's circle: A) Draw Mohr's Circle for the x-y plane. B) Determine the principal stresses - All 3. C) Sketch a properly oriented differential element showing the principal stresses in the x-y plane. D) Determine the magnitude of the maximum shear stress in the x-y plane. E) Sketch a properly oriented differential element showing the maximum shear stress state in the x-y plane. F) Determine the magnitude of the absolute maximum shear stress (and include the two out of plane circles on your original figure). Use the following values for the magnitudes of the stresses: x = 0₂ Txy Ox X X 10 ksi, σy = 4 ksi, σ₂ = 3 ksi, Txy = 4 ksi
QUESTION 4 4.2 4.1 The ratio between the outside diameter and inside diameter of a pipe is 2,5 and the length is 400 mm, when the pipe is not subjected to any load. When a tensile load of 200 kN is applied to the pipe, its length increases by 0,195 mm. The Young's modulus of elasticity for a pipe is 188 GPa. Calculate the inside diameter and outside diameter of a pipe. The following results were obtained by means of a tensile test on a carbon steel specimen, having an original cross-sectional area of 20 mm² and the gauge length is 50 mm. Elastic limit load: Elongation at the elastic limit: =0,06125 mm =4 900 N Maximum load: =7 650 N Load at fracture: =5 050 N Elongation at failure: =15,2 mm Cross-section area at failure: 7,95 mm² Calculate the following: 4.2.1 The stress at the elastic limit. 4.2.2 The maximum stress. 4.2.3 The percentage elongation. 4.2.4 The percentage reduction in area.
Thanks!
The specification of a cylindrical vessel are as follows: D = 350 mm %3D t = 12 mm P = 4.5 MPa Determine the a) Longitudinal Stress; b) Transverse Stress ; and c) new diameter and wall thickness if the 550-mm length cylindrical vessel is replaced by a spherical vessel of the same volume and equal material strength.
Q1. Find the shear stress in aluminum and Steel TAI, TS Use: Gsteel = 85 GPa, GAI= 30 GPa Aluminum Steel D=150 mm D = 50 mm T = 3 kN.m 2.5 m 0.5 m
Show the complete free body diagram for the problem.
The normal and tangential stresses on a plane inclined at 30° to the axis of the minor principal stress are 75 N/mm2 and 20 N/mm2. The resultant stress on a plane by analytical method is