P5.13. Given the moment diagram for each beam, (a) sketch the deflected shape and qualitatively determine (b) the shear diagram and the applied loading. A B C moment A C P5.16. For each beam, draw the shear and moment diagrams, label the maximum values of shear and moment, locate points of inflection, and sketch the deflected shape. 8 kips 8 kips w= 0.3 kip/ft 10'- 10 + 10'- +44

Q: On a map of scale 1:75,000 the map distance measured between points A and B is 5.0 cm. If a sketch…

A: Find scale for sketch of same area

Q: Name four methods of flow measurement?

A: Name four methods of flow measurement?

Q: Problem No. 2: Determine the x and y-coordinate of the centroid of the shaded area.

A:

Q: What is the measurement benchmark

A: The given questions asks about the measurement of benchmark.

Q: When are the singularity functions used?

A: Solution-  We can observe that the shear and bending moment expressions get increasingly complicated…

Q: These lines are called? *

A: Given details Symbol from CAD  CAD - It is Computer Aided Design software .

Q: Subject:Geographic Information System Show how spatial data (Such as Raster Data) analytics are…

A: A system called a geographic information system (GIS) is one that collects, organises, processes,…

Q: Why was the survey foot definition maintained in the United States?

A: Survey foot defination:

Q: Instructions: Solve the following problems. Show your complete solution and illustrations. Box your…

A: Normal stress is σn=12 ksi. Shearing stress is τ=14 ksi. Bearing stress is σb=18 ksi. Based on…

Q: Define the following (300-500 words each) ITEM DESCRIPTION 1.Depth-Area Relationship…

A: In the hydrology aspect, there are several relationships between different parameters such as…

Q: Thank you for you answer, but it's not comlplete. 1- I can't see the right side of the page 2-…

A: Wearing surface of hot mix asphalt with high rut resistance = 225 mm (8.86 inch) Recycled mixture…

Q: late the end areas for depths of fill from 0 to 20 ft using increments of or level sections, a…

A:

Q: Term used in route sureying to describe bends along the lines of roads, railways and canals to bring…

A: Introduction :  Route surveying is a type of surveying used for data collection regarding roadways…

Q: Please fill in the blank for this question please! A *blank* call identifies a corner or boundary,…

A: A _________call identifies a corner or boundary, usually as some object that constitutes the…

Q: computer aided engineering

A: Computer-aided engineering (CAE) is the use of computer software to simulate performance in order to…

Q: ONS B.S. H.I. F.S. LF.S. ELEVATIONS -a 1.24 234.51m 1.11 3.40 4.6 2.8 3.6 2.4 3.21 2.46 1.2 3.2 2.8…

A: Given profile levelling HI = elevation +   BS elevation = HI - FS or IFS given elevation of BM a =…

Q: What is Geodesy & what are the earth models?

A: The mathematical representations of the Earth are established by geodetic systems, which are used in…

Q: Indicate briefly, using words or sketches, how geosynthetics have been used to prevent groundwater…

A: Applications of Geosynthetics that are used to prevent ground water contamination:

Q: Solve for the reactions and draw the shear and moment diagram. 9.35KN/m 2.00 5.00 116KN 9.35KN/m…

A:

Q: Why should one bother to create a punch list on an extranet?

A: The punch list is a checklist that indicates the work left to be completed on a building project.

Q: 12. To make a stretch to an object, the procedure is: left click stretch icon, select the object,…

A:

Q: Line P to Q intersects the street alignment as shown in the sketch below. What is the length of line…

A:

Q: Break the shaded area into the five different areas shown. Find the area and the x- and…

A:

Q: How to create stacked bar chart in tableau

A: This question is related to the Computer-aided design software from Civil Engineering. This is…

Q: SANITARY PLANNING LAYOUT " F. SYMBOLS AND LEGENDS

A:

Q: Level surface, Bubble line, Horizontal line, Level line, Line of collimation, Bench mark, Change…

A:

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: Question 3) (25 points) In a series of experiments, four properties of a material are determined at…

A: The temperature is increased in steps of 5 from 20 to 100. The magnitude of four properties of the…

Q: re there any situations where a scale layer can be helpful to a water utility? (answer in one or two…

A: calcium carbonate form the protective layer on lead pipe by making lead carbonate. which increase…

Q: 8. On a map of scale 1:75,000 the map distance measured between points A and B is 5.0 cm. If a…

A: Solve question 8 and 9

Q: Question 1: Explain in detail how you will carry out surveying of agriculture field using chain…

A: Chain survey is the simplest method of surveying. In this survey, only measurements are taken in the…

Q: Solve for the reactions and draw the shear and moment diagram. 9.35KN/m 2.00 5.00 116KN 9.35KN/m…

A:

Q: 6. For a given soil, density = 2180 kg/m3 and n = 0.3. Determine: a. Void ratio b. Specific gravity…

A: The given data is shown below: Density=2180 kg/m3n=0.3

Q: Do not include the unit in writing the answer. Use small letters (lowercase) in writing Complete the…

A:

Q: 7. Usually the minimum height in the room should not be lower than ( A. 2.2 m B. 2.0 m C. 2.4 m…

A: Note: Multiple questions are asked. Therefore, as per Bartleby guidelines, the answer of only…

Q: What are the advantages and disadvantages of the bar chart ?

A: The advantages of Bar chart are as follows: Bar charts are pretty easy to interpret, and there's a…

Q: What is the measurement benchmark（more than one answer） (multiple choice questions) A. position…

A: Measurement bench mark is a position reference and an elevation datum. It is a point with respect to…

Q: The state of a plane strain at a point has the components ɛ, = -300 (10). ɛy = -400 (106) and Yry =…

A: It is required to determine the normal strain in x direction.…

Q: Hand Writing not allowed please provide Typed answer

A: The distance between v1 and v2 is  √37 or approximately 6.08 units.Explanation:Formula for distance…

Q: Design a project to calculate the moment of Inertia for Circle according to this equation Ix = . The…

A: Structural mechanics is a field of applied mechanics wherein you figure misshapenings, stresses, and…

Q: D#2: Write different uses of Surveying?

A:

Q: What is the elevation of point C?

A:

Q: re text height , arrow size be easily adjusted based on the size of the object? autocad 2.How about…

A: 1. Text can be re-formatted or adjusted for an individual dimension object by selecting the object…

Q: Explain the usage of hazard map.

A: Usage of Hazard Map:-  A hazard map is defined as a map which  highlights the areas that are…

Q: What are velocity charts?

A: The Velocity Chart displays the value amount delivered in each sprint so as to forecast the work…