P4. Consider the switch shown below. Suppose that all datagrams have the same fixed length, that the switch operates in a slotted, synchronous manner, and that in one time slot a datagram can be transferred from an input port to an output port. The switch fabric is a crossbar so that at most one datagram can be transferred to a given output port in a time slot, but different output ports can receive datagrams from different input ports in a single time slot. What is the minimal number of time slots needed to transfer the packets shown from input ports to their output ports, assuming any input queue scheduling order you want (i.e., it need not have HOL blocking)? What is the largest number of slots needed, assuming the worst-case scheduling order you can devise, assuming that a non-empty input queue is never idle? Switch fabric Output port X Output port Y Output port Z

P4. Consider the switch shown below. Suppose that all datagrams have the same fixed length, that the switch operates in a slotted, synchronous manner, and that in one time slot a datagram can be transferred from an input port to an output port. The switch fabric is a crossbar so that at most one datagram can be transferred to a given output port in a time slot, but different output ports can receive datagrams from different input ports in a single time slot. What is the minimal number of time slots needed to transfer the packets shown from input ports to their output ports, assuming any input queue scheduling order you want (i.e., it need not have HOL blocking)? What is the largest number of slots needed, assuming the worst-case scheduling order you can devise, assuming that a non-empty input queue is never idle? Switch fabric Output port X Output port Y Output port Z

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

The words seek time, rotational delay, and transfer time should all be defined. Explain their connection.
Are there significant differences between asynchronous, synchronous, and isochronous connections?
I need the answer quickly
This essay aims to elucidate the distinguishing characteristics between synchronous and isochronous connections, while also presenting an illustrative example for each type?
The X.25 standard specifies a DTE/DCE interface explain?
Please provide an illustration of a synchronous connection and an isochronous connection, and elucidate the distinctions between these two types of connections?
3. Computer A tries to send 6 frames to computer B. The second frame does not arrive correctly (assumed to be lost). Draw the flow diagram using Stop-and-wait ARQ protocol and assuming that the round trip delay is 3 ms and the system time out is 6 ms.
45. Consider the GPIB interface between a talker and a listener as shown in Figure 13-86(a). From the handshaking timing diagram in part (b), determine how many data bytes are actually trans- ferred to the listening device. Talker Listener Data bus DAV DAV NRFD NRFD Transfer bus NDAC NDAC (a) (b) FIGURE 13-86
This is the same question , not different question , please answer the last one too. Give the virtual circuit tables for all the switches after each of the following connections is established. Assume that the sequence of connections is cumulative; that is, the first connection is still up when the second connection is established, and so on. Also assume that the VCI assignment always picks the lowest unused VCI on each link, starting with 0, and that a VCI is consumed for both directions of a virtual circuit. F connects to A
Assume that go-back-n sliding window system has been used for data transmission between two devices. The window is numbered using modulo-n with n=8. Draw the sender and receiver windows if the system is using Go-back-n ARQ for error control based on the following scenarios: A. Frames 0 and 1 are sent, frames 0 and 1 are acknowledged. B.. From answer in Question 1(a), frames 2, 3, 4 and 5 are sent, NAK 4 is received.
Computer Science Write a C program for the ATmega328PB that continuously toggles bits 1, 3 and 6 of Port B every 250 ms without impacting the other bits of Port B. Initialize bits 1, 3 and 6 to values the of 0, 1 and 0, respectively.
A 3400-byte datagram needs to cross a network with an MTU of 800 bytes. i. How many fragments are generated? ii.What are the values of the offset field and the M field for each of the fragments?