P10.1-P10.3 For the loading shown in Figures P10.1-P10.3, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam. (b) the deflection at the free end. (c) the slope at the free end. Assume that EI is constant for each beam. Answer "T A L FIGURE P10.1 L FIGURE P10.2 Mo

Q: On a map of scale 1:75,000 the map distance measured between points A and B is 5.0 cm. If a sketch…

A: Find scale for sketch of same area

Q: Problem Solving: 1. From the given frame shown it is supported by a hinged at A and a roller at C.…

A: To find deflection,  unit load method has been used.

Q: 4" 8" 6"

A: Solution:- Centroid of the given section: Table for calculation  Area inch2 x- coordinate inch y-…

Q: To draw the figure below, the most :important command is Array O Trim O Сopy O Offset

A: Given data Grid of shape To be discussed Which command to be used

Q: 10. In the Transformation-Viewing process, CAD model is defined within the: * Global coordinate…

A: CAD is known as Computer-Aided Design, it is also known as CADD which stands for Computer-Aided…

Q: Subject: Engineering Drawing or AutoCAD Instruction: Draw the 2D Orthographic Projection (Front,…

A: Asked: To draw the orthographic projections of the given object.   The following tools are used to…

Q: continue dimension and baseline dimension?

A:

Q: Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate…

A:

Q: Draw the 3 Principal Views of the object (given unit in mm, convert it to cm) 51 35 15 25 53 73 20…

A: 3D view of the object is provided. We have to draw three principal views of the object.  Three…

Q: 4. An object in isometric view is given as in Figure 3. Draw the object in Third Angle Projection at…

A: An isometric view is given. We need to draw top view, front view and side view

Q: 15.16 Refer to Figure 15.52. Using Michalowski's solution given in Figure 15.25 ('> 0). determine…

A: The kinematic approach of limit analysis is applied to the rigid rotational collapse mechanism by…

Q: For the cross section shown below the coordinates of the centroid in reference to x-y axes shown…

A: Given: A composite cross section Required: x and y coordinate of the cross section

Q: Find centroid of figure from X axis

A:

Q: Describe about the Taylor Charts.

A: Taylor's stability chart are used for determining the stability of slope of cohesive homogeneous…

Q: Give the vector in cartesian coordinates that extends from B(4, 20degrees, 10degrees) to W(7,…

A: The given data is shown below: B=4,20 degrees, 10 degreesW=7,120 degrees, 75 degrees

Q: How to create stacked bar chart in tableau

A: This question is related to the Computer-aided design software from Civil Engineering. This is…

Q: Find the centroidal distances from x axis and y axis

A: Consider the figure,

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: Use the method of compsite areas to calculate the centroidal coordinates of the plane regions shown…

A:

Q: Q.3. Use Scale (1:1), for the front and side views shown draw the isometric projection: 50 30 R30 30…

A: To get the isometric projection from the given views. 1. Draw two lines perpendicular to each other…

Q: Find the scale ratio 1 cm (Map)=6 km (Ground)

A:

Q: What of the following about the scale is/are false ?

A: The scale represents the ratio between the measurement drawn in a plan to the actual measurements.

Q: 50 10 Derive the third projection, taking into account the use of the rules for writing dimensions…

A: GIVEN: TO DETERMINE: TOP VIEW

Q: Figure below represent contour lines for ground surface and wells located on it 50 w2 W1 fill table…

A: given-water table elevation of wells-W1=60W2=50W3=40

Q: QUESTION 4 Find the area of the following shape. Area of the top horizontal rectangle is 27 cm2 and…

A: Top rectangle area = 27 cm²  Bottom rectangle area = 19cm²

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 22 19 38 Ф 18 22…

A: Given Data :

Q: Q3: Draw the Full Sectional Front view and Top View of given object 70 50 10 45 430 70 15 10 88 40

A: The following figure shows the Full Sectional Front View of the object.

Q: Explain 1st and 3rd angle of projection

A: First angle projection and Third angle projection are two different methods of creating a 2D drawing…

Q: What are the types of coordinate system? Illustrate with neat figure.

A: Generally two types of coordinate systems viz, Catesian Coordinate. Polar Coordinate.  Cartesian…

Q: The point Coordinates have unlimited style to appear when inserted in * AutoCAD drawing False True…

A: 1. False. There are 3 types of coordinate display style i.e. static, dynamic and distance and angle.…

Q: Define: First Moment of Area Sketch Or Drawing: Equation: Units:

A:

Q: Locate the centroid of the given area below. Semi-Circle Square

A:

Q: A line CD starting at any point, C, is 8 m long bears N 35° W, and slopes downward from C to D at…

A:

Q: Sketch an ISOMETRIC DRAWING from the attached orthographic projection. Follow the assigned…

A:

Q: 4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch…

A: The levelling terms and formula. BS = Back sight The first measurement taken in a survey. It is the…

Q: graphical presentation for 3D shearing transformation.

A: It is change looking like the article. It is likewise called as deformity. Change can be in the x -…