P1.17 A cylindrical rod of diameter d = 0.625 in. is attached to a plate by a cylindrical rubber grommet. The plate has a thickness of t=0.875 in. If the axial load on the rod is P = 175 lb, what is the average shear stress on the cylindrical surface of contact between the rod and the grommet? -Grommet- Plate

P1.17 A cylindrical rod of diameter d = 0.625 in. is attached to a plate by a cylindrical rubber grommet. The plate has a thickness of t=0.875 in. If the axial load on the rod is P = 175 lb, what is the average shear stress on the cylindrical surface of contact between the rod and the grommet? -Grommet- Plate

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
An 18-m-long steel wire of 10-mm diameter is to be used in the manufacture of a prestressed concretebeam. It is observed that the wire stretches 55 mm when a tensile force P is applied. Knowing that E=250GPa, determine (a) the magnitude of the force P, (b) the corresponding normal stress in the wire
A punch for making holes in steel plates is shown in Figure 3. Assume that a punchhaving diameter d = 20 mm is used to punch a hole of 8 mm plate. If force, V = 110 kNis required to create the hole, determine the shear stress in the plate.
PROBLEM 1 A circular aluminum tube of L=600mm is loaded in by compressive forces at its ends. The outside and inside diameters are 75mm and 63mm respectively. A strain gage is placed on the outside of the tube to measure nomal strains in the longitudinal direction. E=73 GPa and Poisson's is 0.33. a. If the normal stress in the tube is 57 MPa, what is the load P? b. if the strain is 781 X 10-6, what is the shortening of the tube? What is the percent change in its cross-sectional area.
None
The compound shaft has a uniform cross-sectional area with the given length of each segment. Using the applied torque on the indicated position, determine the safe diameter of the shaft if the allow stress in each segment is shown and the free end angular deformation is limited to 2.8° Hint: 3 different diameters from stress analysis One answer of diameter from angular deformation. 90DN-m A Treactuon 75DN/m 1200N-m 3.4m 15m 2.3m Allow Torsional Segment Stress G 70 Gfa AB 89GPA BC 28GP. CD GOMPA 75 MPa 50 MPa'
222. two decimal places
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=34 kips is applied to the assembly at A, two loads of Q=25 kips are applied at B, and two loads of R=37 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 32 ksi. The normal stress magnitude in brass rod (3) must be limited to 24 ksi. Determine the minimum diameter (in in rounded to the nearest thousandths) required for rod 2.
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A?in micro rad Determine the shear strain γnt at point A?in micro rad What is the normal strain in the x-direction?micro£
2. A copper rod of diameter 12 mm is subjected to a compressive force of 8 kN. The change in diameter happens to be 4.5 x 103 mm. Determine the strain along the length of the material and the Poisson's ratio when E = 110 GPa.
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm