P = 8.0 kN A cantilever beam of length L 2 m supports a load P 8.0 kN (see Figure 4). The beam is made of wood with cross-sectional dimensions 120 mm x 200 mm. Calculate the shear stresses due to 200 mm the load Pat points located 25 mm, 50 mm, 75 mm, and 100 mm from the top surface of the beam. L=2 m 120 mm Figure 4

Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…

A:

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: What is the most common scale used for temperature

A: The Celsius and fahrenheit scale is used most commonly used.. Kelvin scale is primarily used in…

Q: How do you make Industrial diamonds

A: Industrial diamond:-  Industrial Diamond is any diamond which was designated for the industrial use…

Q: Convert a scale of 3 2/3 feet to 4 inches to a scale factor.

A:

Q: Convert 24 inches to feet.

A:

Q: Draw the three projections showing the measurements, thanks for the cooperation

A:

Q: can you please explain your calculations? Im not sure on how you got 2 for the first part

A: Given: The velocity distribution in the boundary layer is given by the expression: uU=1-exp-2×yδ The…

Q: Identify the length of line A, B, and C. Create/Draw top view, left view, front view, and bottom…

A: Answer  Length of line A = 9.0-4  Length of line A = 5 Length of line B = 13.5-11.52 Length of line…

Q: How is unit weight expressed in primary dimensions?

A: Unit Weight is defined as the Weight of soil per unit volume.

Q: Solve for the reactions and draw the shear and moment diagram. 9.35KN/m 2.00 5.00 116KN 9.35KN/m…

A:

Q: express each measurement in feet.42 inches

A: Given: The measurement is 42 in.

Q: Draw the Top, side, frotn view of the figure below

A:

Q: How are units converted using dimensional analysis?

A:

Q: Convert 1600 mils into equivalent value in grads O 90 degrees O 180 degrees O 270 degrees

A: To convert mils to degree

Q: Is there any simpler way to calculate this?

A:

Q: Convert 6.2 feet to inches.

A: Given: The measurement is 6.2 ft.

Q: If the actual dimension is 46 m and the scaled dimension is 184 cm, what is the scale used?

A:

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: The force of shear is a sensitive force on the surface. It's said to be the bending moment the…

Q: A drone is flying in the air at some altitude. The drone is equipped with piezometer that indicates…

A:

Q: ooking at the X direction, provide the front view, top view, and left-side view using the meter…

A: The isometric Front, and side. Top view of above drawing is given below:

Q: Solve for the reactions and draw the shear and moment diagram. 9.35KN/m 2.00 5.00 116KN 9.35KN/m…

A:

Q: H MM 0 10 20 30 40 50 60 70 80 90 100 DIMENSION THE PART USING METRIC DIMENSIONS. USE DIVIDERS OR…

A: The front view and top view of an object is shown in the above figures. Also scale of dimensions…

Q: Do not include the unit in writing the answer. Use small letters (lowercase) in writing Complete the…

A:

Q: What are the metric and/or SI units typically used in a Factor of Safety Calculation?

A: In the field of engineering, the factor of safety (FoS) is a dimensionless parameter used to…

Q: What is area of plot in rectangle shape. Length =20feet, breadth=10 feet.

A: Finding area of rectangular plot Given: length= 20ft Breadth=10ft

Q: express each measurement in feet.50 inches

A: Given: The measurement is 50 in.

Q: Determine the centroidal coordinates (x, y,z) of the volume.

A: Question is based on the section . Dimension of section are given in the question . Centroidal…

Q: Isobel and Neliwe’s garage floor is 5400 mm long and 3000 mm wide.  The floor plan of Isobel and…

A: Scale can be defined as the ratio of the dimension in plan or map to the actual dimension  Scale is…

Q: express each measurement in feet.108 inches

A:

Q: Solve for the reactions and draw the shear and moment diagram. 116KN

A: PLEASE POST OTHER QUESTIONS IN DIFFERENT QUESTION

Q: 33. Write an algorithm to sums all the even numbers between 1 and 20 and then displays the sum. 32…

A:

Q: 5 bar equals to

A: To find : To convert bar to pascal.  Given: 15 bar pressure.

Q: Figure 20-7 Questions 1-10. 44 8. 6 38 20 24 34 Ol 76 8 80 84 88 92 10 Match the dimensions…

A:

Q: Determine the following: 1. Height of the object 2. Width of the object 3. Depth of the object…

A: 1. Height of the object = 2 + 1.25 = 3.25 ( Hint : Measured from Front View) 2. Width of the object…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.