P = 2 MPa T= 400°C V = 50 m/s Z1 = 10 m Q4: (Section B) The power output of an adiabatic steam turbine is 5 MW, and the inlet and the exit conditions of the steam are as indicated in Figure. Find: STEAM (1) The work done per unit mass of the steam flowing TURBINE Wout =5 MW through the turbine. (2) The mass flow rate of the steam. P = 15 kPa 2 = 90% V2 = 180 m/s 22=6 m (Use Table A-5-1 and Table A-6-2) %3D

P = 2 MPa T= 400°C V = 50 m/s Z1 = 10 m Q4: (Section B) The power output of an adiabatic steam turbine is 5 MW, and the inlet and the exit conditions of the steam are as indicated in Figure. Find: STEAM (1) The work done per unit mass of the steam flowing TURBINE Wout =5 MW through the turbine. (2) The mass flow rate of the steam. P = 15 kPa 2 = 90% V2 = 180 m/s 22=6 m (Use Table A-5-1 and Table A-6-2) %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump delivers water between a reservoir and a water tank. The surface waterelevation of the water tank is 20m higher. The suction side contains an entrance strainer (Ks=2.5), and50m of PVC pipe that is 25cm in diameter. The discharge side includes a 200m long PVC pipe, 25 cmin diameter, and a gate valve. The net positive suction head (NPSH) is 7.5m, and the design discharge is150L/s. Determine the allowable elevation difference between the pump and the reservoir water surface,z s, to avoid cavitation. Assume a kinematic viscosity of 1x10-6m 2 /s and a specific weight of 9.79kN/m 3 .
Mechanical Engineering A steam turbine receives hot & pressurized steam from the inlet (port 1 in the figure), produces work, and discharges steam at low pressure and temperature to the outlet (port 2). P1 = 1.5 x (modifier) MPa, T1 = 350 x (modifier) °C. P2 and T2 are given in the figure. The turbine is at a steady state. Kinetic energy and gravitational potential energy of the steam are negligible compared to its thermal energy. q is negligible Turbine w? P1= T = im =16 kg/s 2+ P, = 0.2 Mpa | T, = 150°C (a) Mass flow rate at the inlet is 10 kg/s. Compute the mass flow rate at the outlet. Show your reasoning (b) Determine the change of specific enthalpy of the steam between the inlet and the outlet. You can assume the specific heat of steam remains essentially constant during the process, with C, = 1.9 kJ/kg.K (c) Compute the work produced by the steam turbine, per unit mass of steam. (d) Compute the power production from the turbine. Power is the work produced per time, and its most…
Air enters a duct (100 cm *10̟cm*10 cm) at 32°C at a rate of 0.28m /min to cool 138 W electronic component placed on the duct. Assuming 85 percent of the heat generated inside is transferred to air flowing through the duct and the remaining 15 percent is lost through the outer surfaces of the duct. What is the exit temperature of air (°C)? C,= 1007 J/kg.°C, v =1.654×10-S m²/s, p 1.146 kg/m Pr = 0.7268, k = 0.02625 W/m.°C Select one or more:
When passing through an adiabatic turbine (figure), bullet steam at 500 °C and 3.5 MPa expands to 200 °C and 0.3 MPa, it flows at a flow rate of 529 oz/s, what is the power Specified by the turbine in kW if the piping at the same inlet is D1 = 5.90 in diameter and at the outlet, D2 = 0.82 ft in diameter? Data: for steam at initial conditions Hi = 3450.9 kJ/kg at final conditions, H2 = 2865.6 kJ kg; Specific volume of steam in the initial condition = 0.0992 m²/kg; Specific steam volume in the final condition = 0.7163 m/kg. %3! %3D
Shown below is a motor rising a 5 kg mass. If the solar panel shown receives solar energy at a rate of 900 W/m?, if its area is 2 m², the voltage that it produces is 12 V and its efficiency is 15 %. (a) How much current is the solar panel producing? . (b) What is the rate of heat dissipation? (c) How fast is the motor dissipating heat? (d) At what velocity will the mass shown rise. Assume that the temperatures remain the same all through the system and that the angular velocity of the motor is constant. Area = 2 m² AV = 12 V O = ? G = 900 W/m? n = 15 % n = 85 % IR = 0.2 m i = ? Motor Q = ? m = 5 kg in
Explain the placement for these item in the system: - Steam turbine - Gas turbine - Heat pump (i need to do a presentation, can you explain to me. for me to become more understand this topic?)
Consider the same problem in which an axial compressor with a mean diameter of 0.8 m is being designed to run at 3000 rpm. The whirl velocities at the inlet and outlet are 5m/s and 30 m/s, respectively. The air mass flow rate through the compressor is 2 kg/s at a temperature of 27 °C. Assume C, of air equal to 1000 J/kg-K and Cy = 718 J/kg-K. %3D The temperature change is equal to O 3.14 K 5.28 K 7.42 K OOK
pls show complete solution
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the value of G in kg/s.m2?. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
An ideal gas passes a diffuser. At the diffuser inlet, the temperature is T1 = 350.00 K, the pressure P1 = 100.00 kPa, the velocity V1 = 200.00 m/s, and the inlet area A1 = 0.30 m2. At the exit, the velocity is very small. The specific heat of the ideal gas at the constant pressure is cp = 1.0050 kJ/(kg·K). The gas constant is R = 0.2870 kPa·m3/(kg·K). Determine the enthalpy per unit mass at the exit, h2__________(kJ/kg)
A frictionless piston/cylinder assembly A shown in the figure is connected by a thin pipeline with a valve to a rigid tank B. The volume of tank B is 1.0 m³, and the cross-sectional area of the piston is Aa = 1.2 m?. Initially (state 1) the valve is closed, 3 kg of argon is enclosed in the piston/cylinder assembly, mĄ1 = 3 kg, and there is no argon in the tank, mg,1=0. The initial temperature of the argon is TĄ1 = 50°C and the initial volume of the gas enclosed by the piston cylinder is VA1 = 1.5 m?. The valve is slowly opened allowing argon to flow into the tank. The valve is then closed when the piston just touches the stops but does not exert a force on the stops (state 2). At state 2, the temperature and pressure throughout the tank and piston/cylinder system are equal (Pa2 = P8,2 and Ta2= T82). The height from the bottom of the cylinder A to the top of the stops is htops = 0.5 m. The volume of the stops can be assumed negligible. Treat argon as an ideal gas. a) Determine the…