pls give me answer oveOriçefDesign:For a Rressure vessel D= 4 , internal pressure- 50 MPA, st - 190 MR ; 61 = 196 NPa /Find Safe thickness:PONa: 6t =PDナ;?Larger thickness is Safer.LFrachureAR,6t is greeter so, fractorewill be due to 6t,a in lorgitudinal diroction.

Given data: The diameter of the cylinder is D=400 mm The internal pressure is P=50 MPa The hoop…

Oricef Design. For a Riessure vessel D= 4 , internal pressure : 50 MPA, st = l40 MR ; 61 = 196 NPa Find Safe thickness. PD Larger thicknss is Saten. A, 6t is greater so, frachure will be dueto 6t, a in lorgitudinal diroction.

Oricef Design. For a Riessure vessel D= 4 , internal pressure : 50 MPA, st = l40 MR ; 61 = 196 NPa Find Safe thickness. PD Larger thicknss is Saten. A, 6t is greater so, frachure will be dueto 6t, a in lorgitudinal diroction.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 3) On the plate in the figure, the length L is given as L = 18 m . According to this; y 2L L 2L 3 L -- L Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result as m without writing units.) Response: Question 3-B) Find the Y coordinate of the geometric center of the plate . (Enter your result as m without writing units.) Response:
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
Question 3) The length L is given as L=34 m on the plate in the figure. According to this;Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)Question 3-B) Find the Y coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)
HANDWRITTEN. answer 4 5 6 then box the final answers
a diagonal of a polygon is a line segment that connects nonadjacent vertices of the polygon.in the following polygons, a triangle has 3 sides and 0 diagonal, a quadrilateral has 4 sides and 2 diagonals, a pentagon has 5 sides and 5 diagonals, a hexagon has 6 sides and 9 diagonals. predicts the number of diagonals in a 12-sided polygon.
Solidworks
Oz Lawn Care Inc. manufactures and assembles lawnmowers that are shipped to dealers throughout the United States and Canada. Two different procedures have been proposed for mounting the engine on the frame of the lawnmower. PB (Minutes) UPB (Minutes )345798632 5 Is there a difference in the methods' mean time to mount the engines on the frames of the lawnmowers? The answer must be in handwriting. Please write your answer using a ball - point pen on plain paper. Submit your homework by uploading it to the canvas. Good Luck!
Q6 Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke length of 400 mm. What is the engine capacity in litres? Give your answer to 2 decimal places.
please hand written solution please hand written solution please hand written solution