|E PROBLEM 8 USING THE METHOD OF JOINTS, DETERMINE THE FORCE IN EACH MEMBER OF THE TRUSS SHOWN IN THE FIGURE. INDICATE WHETHER THE MEMBERS ARE IN TENSION OR COMPRESSION. 4 ft 4 ft- 3000 lb 1000 lb L. Lond

Q: You have decided to build a deck on your new home 12 feet wide x 16 feet long, using the standard 2…

A:

Q: Provide the sectional front view, looking at the direction X, draw the top view, and left-side view…

A:

Q: Draw orthographic views of the figure with dimensions

A: The isometric view the three dimensional which is drawn in the two dimension.  The orthogonal view…

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: With the measurements in the following table, calculate the soil moisture flux q (cm/day) between…

A:

Q: Is/ are graphical representation of arrangement of geological and structural features of a…

A:

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: Determine external and total indeterminacy

A: Given data : Number of external support reaction (R)=2+1=3Number of member (m)=3Number of joint…

Q: What is the most common scale used for temperature

A: The Celsius and fahrenheit scale is used most commonly used.. Kelvin scale is primarily used in…

Q: 16m 8m 60° 126m 120m 20m 64m 16m

A:

Q: Draw and Isometric view of a hexagonal pyramid of side 30 mm and height 50 mm

A: The isometric view is the three dimensional projection of the object in two dimension vies.  And the…

Q: For any engineering example discuss with drawing the Bathtub Curve

A: The bath tub curve is generally used in reliability engineering.   This curve signifies the…

Q: Differentiate force system based on line of action.

A: A force is a push or pull on an object caused by its interaction with another object.

Q: Discus the sequence of the different stages of prestressing a beam, in 10 sentences or less. Provide…

A:

Q: Define the pressure versus volume ?

A: Pressure is force divided by the area over which it acts . Volume is the amount of space is taken up…

Q: Find the centroidal distances from x axis and y axis

A: Consider the figure,

Q: Given the following isometric drawing, draw the top view, front view, and right side view

A:

Q: DETERMIME Fou つ こ I =

A:

Q: A drone is flying in the air at some altitude. The drone is equipped with piezometer that indicates…

A:

Q: What is beam

A: The amount by which a beam deflects upon its cross-section, bending moment and shear force. For…

Q: - 4- पिक (17 b=260m- de-Sm h= 300m = 204N/m to 2onm M= <40kN b f=30kW

A: Given. Udl =20kn/m bending moment 40knm Point load 30kn Draw sfd bmd

Q: 60 Looking at the x direction, provide the front view, top view, and left-side view using the meter…

A: WE HAVE TO DRAW THE LEET SIDE , FRONT VIEW AND TOP VIEW   Looking at X direction, we conclude that…

Q: 200N 30 R, "y at point C

A:

Q: Determine the centroidal coordinates (x, y,z) of the volume.

A: Question is based on the section . Dimension of section are given in the question . Centroidal…

Q: Find

A:

Q: Q3: Draw the Full Sectional Front view and Top View of given object 70 50 10 45 430 70 15 10 88 40

A: The following figure shows the Full Sectional Front View of the object.

Q: draw an isometric view of HEXAGONAL PRISM  where the base is 25mm and height 50mm.

A: Isometric view: It is also known as isometric projection. It is defined as the visual representation…

Q: What are the types of coordinate system? Illustrate with neat figure.

A: Generally two types of coordinate systems viz, Catesian Coordinate. Polar Coordinate.  Cartesian…

Q: 100 N 100 N 100 100 150 250

A:

Q: 150 25 40 185 25 75 50

A: To draw the front, top and side view of the given object. Given 3d object:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?