Operational amplifier (Op-Amp) Exercise In a certain application, a signal source having 60 kn of source impedance, Rs, produces a 1 Vms signal. This signal must be amplified to 2.5 Vrms and drive a 1 kN load. Assuming that the phase of the load voltage is of no concern, design an operational amplifier circuit for the application. Hint: Choose, arbitrarily, input resistor, R1 100kn and find feedback resistor, Rf. Since phase is of no concern and the required voltage gain is greater than 1, we can use either an inverting or noninverting amplifier. Answers: Rf (inverting) = 400 k2, Rf (noninverting) = 150 kN

Operational amplifier (Op-Amp) Exercise In a certain application, a signal source having 60 kn of source impedance, Rs, produces a 1 Vms signal. This signal must be amplified to 2.5 Vrms and drive a 1 kN load. Assuming that the phase of the load voltage is of no concern, design an operational amplifier circuit for the application. Hint: Choose, arbitrarily, input resistor, R1 100kn and find feedback resistor, Rf. Since phase is of no concern and the required voltage gain is greater than 1, we can use either an inverting or noninverting amplifier. Answers: Rf (inverting) = 400 k2, Rf (noninverting) = 150 kN

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ql:A: Design a multi-range ammeter of 0.5 and I Amp. using a PMMC(galvanometer) of 500 internal resistance and full-scale current of 1 ma. Show the way of connection with the load RL.
Draw the circuit diagram of the basic noninverting amplifier configuration. Give an expression for the closed-loop voltage gain of the circuit in terms of the resistances, assuming an ideal op amp. Give expressions for the input impedance and output impedance of the circuit.
The ideal op-amps depicted can swing rail-to-rail at output, and Vcc= 13 V. Initially, the output voltage Vo = +13 V and the input voltage is vS = -13 V. The feedback resistors are R1 = 6.4 k0, R2 = 8.5 kQ, and R3 = 1.6 KQ. If the input voltage is gradually increased, at what value of vS (to 1% accuracy) does the output voltage (Vo) change to Vo=-Vcc? VVV vS = + R10 Vcc -Vcc R20 04 O Vo
Design a collector-feedback circuit using with Vcc = 5 V, Ic = 10 mA, and VCE = 1.5 V.
give short answer in 10 minutes i will give positive feeback
Given in the figure is a two-stage amplifier design that employs negative feedback. Answer the following questions. Use the notation (R1 + R2 + ... + Rn) for series resistors and (R1 || R2 || ... || Rn) for parallel resistors for clarity and ease. Assume that the transistors are already biased properly in the saturation region and ro1 = ro2 → ∞. Also assume that the capacitors have infinite capacitance. 1.) Find the expression for the open loop gain Av 2.) Derive the resistance Rin which is the resistance that can be seen at the input port of the amplifier
Perform an ac analysis. Represent the amplifier by its ac equivalent circuit and discuss the input resistance at the base and the output resistance. (You can draw the circuit by hand on paper and can paste the image)
give short answer in 15 minutes i will give positive feeback
Four voltage sources of 3 V, 4V, 2V and 3V respectively are to be applied to the input terminal/terminals of “an" inverting amplifier. Design two different circuits for the two different cases with justified explanation and selection of proper resistances as per the requirements below: a) When an output of 4V is required (with phase shift). b) When an output of 8V is required (without phase shift) Note: Only inverting amplifier/amplifiers to be used for each case and all the voltage sources are to be used for each individual design as required in a) and b). 2.
An operational amplifier consisting of three cascaded stages has a voltage gain of 3500. The gain of the first two stages is known to be -5 and -900. What is the voltage gain of the last stage and which type of MOSFET amplifier would you prefer for this stage?