Open with F2 = 310 N R F1 :730 N 100 mm 100 mm 250 mm а) Determine the magnitude of the resultant R for the F1 and F2 combination. b) Where should the resultant force R act in order to result in the same external effect that will be caused by the combination of F1 and F2 alone. (Your answer should be the value of d in the figure) In addition toR when d is 50mm, find the magnitude of 2 force P's to be applied horizontally through points B and C in order to form a couple that will result to the same external effect that will be caused by the combination of F1 and F2 alone. Is the couple caused by the 2 force P's c) clockwise or counter-clockwise?

Open with F2 = 310 N R F1 :730 N 100 mm 100 mm 250 mm а) Determine the magnitude of the resultant R for the F1 and F2 combination. b) Where should the resultant force R act in order to result in the same external effect that will be caused by the combination of F1 and F2 alone. (Your answer should be the value of d in the figure) In addition toR when d is 50mm, find the magnitude of 2 force P's to be applied horizontally through points B and C in order to form a couple that will result to the same external effect that will be caused by the combination of F1 and F2 alone. Is the couple caused by the 2 force P's c) clockwise or counter-clockwise?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

F1 F2 b M a C A a a Given the system above, F1 = 34 N, F2 = 96 N, M = 245 N-m, a = 3 m, b = 2 m, and a = 40°. %3D (a) Represent the system using a single force. Determine the magnitude of the force and its location relative to point A. Round all answers to the nearest integer. The magnitude of the force (N) is: N The position of the force relative to A (m) is: m (b) Represent the system using a force and a couple moment acting at point C. Determine the magnitudes of the force and the couple moment. Round all answers to the nearest integer. The magnitude of the force (N) is: N The magnitude of the couple moment (N-m) is: N-m
((last two digits 68)) In the figure, the forces F₁ = 40 N, F₂ = 100 N, and F3 = N, i- Determine the sum of the moments of the forces about point A. ii- Determine the smallest force at D that create the same moment about A. Use the last two digits of your ID number for force F3 = N A T EU 3 m 45° | F₂ 5 m 30° F3 F₁₁ D B
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 13700 ksi] rods, and a solid steel [E = 32600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.84 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.5 in. Assume L1=37 in and L2=66 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 27 kips is applied. (2) (1) L2 (1) L1 A P
The circular shaft AB consists of a 18 mm diameter solid steel cylinder in which a 8 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 50 Nm. Determine the ratio of lengths L₁/L₂. Input your answer to two decimal places. 4₁ L₂ A 150 Nm B
1. A 200mm x 300mm beam has a simple span of 8 meters. It is necessary to place a support at midspan because of the excessive deflection at the center in order to limit the deflection to 12mm and such that the moment at that point is zero. E = 13,800 MPa. a. Determine the load carried by the beam. Express your answer in N/m. b. Compute for the reaction at the support at midspan so that the beam will not deflect at its midpan. c. Find the bending stress of the beam so that it will not deflect at its midspan. W- N/m 4m Pz 200 mm RI 300mm
Use x = 137 y = 37 a = 6 b = 8 c = 1
Use X = 137 Y = 37 A = 6 B = 8 C = 1
Use X = 137 Y = 37 A = 6 B = 8 C = 1
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 14800 ksi] rods, and a solid steel [E = 32200 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.68 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.54 in. Assume L1=50 in and L2=81 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 21 kips is applied. (2) (1) L2 (1) |L1 B P.
Find the maximum moment of the given load train at point n on the beam given in the figure?
Question 5 T/2 В 1200 Nm A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member BC. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm
2.1.5