Answered: OOO A soap bubble of 60 mm diameter has…

OOO A soap bubble of 60 mm diameter has a gauge pressure of 2 N/m Estimate the surface tension of bubble. Select one: O 0.10 N/m 0.3 N/m 0.015 N/m 0.22 N/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: If the pressure difference between the inside and outside of a soap bubble of 3mm diameter is 16…

A: Given data- Pressure difference ∆P=16 N/m2dia of the soap bubble d=3 mmTo Find-The surface tension σ

Q: figure 5 shows a manometer being used to indicate the difference in pressure between points A and B…

A: Question is based on the concept of manometer. A manometer is given in the questioncontains water…

Q: Small-diameter, high-pressure liquid jets can be used to cut various materials as shown in the…

A: Reference : Fluid mechanics,Water jet pressure. Given : 0.1 mm diameter and 690 m/s To find : 1.…

Q: 10. Calculate the density, specific weight, and specific volume of chlorine gas at 25°C and pressure…

Q: It is not a component in the equation describing the pressure drop across a pipe carrying solids by…

Q: In the figure shown, determine the gage pressure at B when its absolute pressure is 290 kPa. Encode…

A: DETERMINATION OF GAUGE PRESSURE AT B ###

Q: Q7. If a soap bubble has to sustain an absolute pressure of 101.35 kPa with its diameter being 25 mm…

Q: Pipe Water Ah SG = 2.6 D = 30 mm Figure Q2 (a)

Q: 2.48 A spherical soap bubble has an inside radius R, a film thickness t, and a surface tension o.…

Q: The pressure drop in a system is dependent on the ff quantities: fluid velocity, fluid density, pipe…

A: Buckingham ' s Pi theorem states that: If there are n variables in a problem and these variables…

Q: The excess of pressure in a soap bubble of diameter 10 mm, when the surface tension is 0.04 N/m is…

Q: If a soap bubble has to sustain an absolute pressure of 101.35 kPa with its diameter being 25 mm…

Q: The surface tension in a soap bubble of 20 mm diameter, when the inside pressure is 2.0 N/m2 above…

Q: f the pressure in the tank of oil (sp gr 0.80) is 60 psi, what is the equivalent head in feet of oil

Q: Small-diameter, high-pressure liquid jets can be used to cut various materials as shown in the…

Q: Determine the volume of the solid in the pipe shown in the figure below. Show complete solution with…

A: Given:- Height of cylinder, h=18 mmOuter radius of cylinder, ro=8 mmInner radius of cylinder,…

Q: PROBLEM 3. Compute the capillary effect of immersion in water of a glass tube of 4mm internal…

A: The values given in the question are as follows Diameter of tube(d)=4 mm or 4*10-3 m Surface…

Q: After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of…

A: Depth upto which SAE oil is filled in a glass to make it float on water = d , Specific Gravity og…

Q: A glass cylinder 5 cm internal diameter with a screen at the bottom is used as a falling head…

A: Solution: Given: Glass cylinder inner dia. = 5 cm = 50mm Area of the cylinder = π4×d2=π4×52=19.635…

Q: ← Fluid Properties The diameter of droplet is 0.075 mm. What is the intensity of the pressure (N/sq.…

A: Given Data Diameter of droplet (d) = 0.075 mm Surface tension = 0.000075 N/mm Find the intensity…

Q: PROBLEM 3. Ifa pressure applied to 1 kg of water is 13.2 x 10^7 N/m 2 causes a percentage reduction…

Q: A fluid's viscosity and unit weight are reduced to 60% and 80%, due to increase in temperature. If…

A: Given data- Fluid's viscosity & unit weights are reduced to 60% & 80%, All other parameters…

Q: A thin 15x10 cm plate is pulled at 2.2 m/s horizontally on a 3 mm thick oil layer with a stationary…

A: Given Area 15×10 cmViscosity 0.025 pa secThickness 3 mmVelocity 2.2 m/secTo find out Force required…

Q: 2.52 A water column in a glass tube is used to measure the pres- sure in a pipe. The tube is 1/4 in.…

A: When a small diameter tube is inseated into a liquid, there may rise or fall occurs in liquid level…

Q: Determine the volume of the solid in the pipe shown in the figure below. Show complete solution with…

A: Given data: Solid pipe radius, R= 8-4 mm R = 4 mm Height of the pipe, h = 18 mm

Q: The vertical reducing section shown in the figure contains oil with S flowing upward at the rate of…

Q: The 100-mm-diameter commercial steel pipe discharges water at 25°C through the 40-mm-diameter…

A: The 100-mm-diameter commercial steel pipe discharges water at 25°C through the 40-mm-diameter…

Q: A gas expands from 0.03 m3 to 0.05 m3 at constant pressure of 3.5 atm. Determine the work done.

A: The initial volume is V1=0.03 m3. The final volume is V2=0.05 m3. The pressure is P=3.5 atm. The…

Q: What is the difference in the heights of the two water columns? Assume that the glass is very smooth…

A: To determine the difference in height of the water columns. To solve the given problem, one must…

Q: Q3. A. soap bubble 60.0 mm in diameter has an internal pressure in excess of the outside pressure of…

Q: Problem 6. What is the bulk modulus of a liquid which is compressed in a cylinder from a volume of…

A: Given data : Initial pressure (P1)=80 N/cm2Final pressure (P2)=150 N/cm2Initial volume (V1)=0.0125…

Q: Q.50 Uniaxial compression test data for a solid metal bar of length 1 m is shown in the figure.…

Q: Glycerin flows through a 5 pressure at A is PA = 113 Figure

Q: oil (56 0.8) Patm - lol KR. For the shown figure, determine the pressure in gas pipe? Pgas =? 2,02 1…

A: Given:- The specific gravity of the oil = SG = 0.8 The atmospheric pressure = Patm = 101 kPa at 20o…

Concept explainers

Pressure and Stress

Question

A soap bubble of 60 mm diameter has a gauge pressure of 2 N/m
Estimate the surface tension of bubble.
Select one:
0.10 N/m
0.3 N/m
O
0.015 N/m
O
0.22 N/m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The closed cylinder shown is filled with water to a depth of 100mm and rest with air. What is the pressure at the bottom of the periphery of the tank? 0.02 0.10 AIR 0.20
E10
Answer correctly thank
Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume the flow is laminar. Note: In answering the question, it must be in exponential form but in the text box just write the value no need to include the x10^-1.. 9 ft L=6 ft d=in B Q
Fluid mechanics
9.45 A sphere of diameter D and density p, falls at a steady rate through a liquid of density p and viscosity . If the Reynolds number, Re=pDU/μ, is less than 1, show that the viscosity can be determined from u gD²(p. - p)/18 U.
Problem- Find the surface tension in a soap bubble of 50 mm diameter with its inside pressure being 2.5 N/m² above the atmospheric pressure.
10
Read the question carefully and give me right solutions with clear calculations
Question #1 A hole having a diameter of 75 mm is cut out from a uniform plate of diameter 240 mm. The distance between the center of the plate and center of the hole is 50 mm. Determine the position of the center of gravity of the remaining material.
I need the answer as soon as possible