Solve it correctly please. I will rate accordingly One mole of water vapor at 343to 298 K. The heat given off by the coolingwater vapor is absorbed by 9 mol of an idealgas, and this heat absorption causes the gas toexpand at a constant temperature of 273 K.If the final volume of the ideal gas is 26 L,determine its initial volume. The specific heatof water is 4186 J/kg.° C and the latent heatof vaporization is 2.26 x 106 J/kg.Answer in units of 1.

Answered: Image /qna-images/answer/9fd52332-7516-4b31-9f83-89e1118c0533.jpg

One mole of water vapor to 298 K. The heat given off by the cooling water vapor is absorbed by 9 mol of an ideal and this heat absorption causes the gas to gas, expand at a constant temperature of 273 K. If the final volume of the ideal gas is 26 L, determine its initial volume. The specific heat of water is 4186 J/kg.° C and the latent heat of vaporization is 2.26 x 10 J/kg. Answer in units of 1.

One mole of water vapor to 298 K. The heat given off by the cooling water vapor is absorbed by 9 mol of an ideal and this heat absorption causes the gas to gas, expand at a constant temperature of 273 K. If the final volume of the ideal gas is 26 L, determine its initial volume. The specific heat of water is 4186 J/kg.° C and the latent heat of vaporization is 2.26 x 10 J/kg. Answer in units of 1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve it correctly , Don't Use Ai tool. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.
estion 4 What is the value of the dimension measured on the following Vernier Caliper in mm? t yet swered rked out of cm 00 3 4 6 7 89 10 Flag question Main Scale Vernier Scale Select one: O a. 1.65 mm O b. 11.65 mm O c. 9.65 mm O d. 10.65 uestion 5 Determine the rotational speed in rpm of the shaft of diameter 30 mm if the cutting sneed 50 m (min
Find the value of the dedendum for a 20 degree full-depth involute (coarse pitch) gear with a circular pitch of 7.5 inches per tooth. A 2.93 B 2.87 C 2.78 D 2.39
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. Find the axial force transmitted by the gear. A 252.26 lb B 225.26 lb C 522.26 lb D) 552.26 lb
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
MECHANICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SHOW THE STEP-BY-STEP PROCESS WITH SHORT COMMENT/EXPLANATION. ANSWER IN 4 DECIMAL PLACES. Determine the torque (in N-m) applied to the shaft of a car that transmits 450 hp and rotates at a rate of 3000 rpm.
73 alll & O... Q1:- The objective of the gear train is to calculate:- 17 responses Speed ratio Number of gear 29.4% teeth The applied torque 5.9% All of these None of these 58.8% Q2:- The speed ratio of a compound gear train can be obtained by using the following Copy chart formula:- 17 responses Product of teeth on driven gears divided by the 11.8% product of teeth. Product of teeth on driver gears divided by the product of teeth. 5.9% Product of teeth in driven aears
1)In a simple micrometer with screw pitch 0.5 mm and divisions on thimble 50, the reading corresponding to 5 divisions on barrel and 12 divisions on thimble is
Answer the attached file
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. What is the value of the circular pitch in mm per tooth?
Q1 (a) Figure Q1(a) shows a gear system. Find (i) The relationship between the number of the gear teeth N1 & N2 and the radius rl & r2 (ii) The distance travelled along the surface of each gear (iii) The work done of each gear
1. Two gears mounted on shafts have 10 and 15 teeth, respectively. The center distance is 10 in. The addendum equals the module, and the clearance equals 0.15 times the module. Determine (a) pitch diameters, (b) addendum, (c) dedendum, and (d) root circles.